Val Controls IDC24-A Скачать руководство пользователя страница 47

Страница: 47 / 74

DID-UM-002

Val Controls A/S

•

Limfjordsvej 3

•

DK-6715 Esbjerg N

•

Tel. +45 7547 0600

[email protected]

•

www.valcontrols.com

Revision: 10

47/74

8.3

Full stroke errors (451 to 468)

No. 451

FST start condition: Not at operational

Description

The valve is not at the operational position

Trouble shooting

This error can be solved by

•

Make sure the valve is at the operational position

•

Perform an endpoint calibration.

•

Increase the full stroke position deadband

No. 452

FST start condition: Low start pressure

Description

The measured pressure is below Start pressure low

Trouble shooting

This error can be solved by:

•

Increase the pressure in the hydraulic/pneumatic system

•

Decrease the Start pressure low value

No. 453

FST start condition: High start pressure

Description

The measured pressure is above Start pressure high

Trouble shooting

This error can be solved by:

•

Increase the pressure in the hydraulic/pneumatic system

•

Increase the Start pressure high value

No. 454

FST start condition: In ESD mode

Description

Emergency shutdown is detected

Trouble shooting

This error can be solved by:

•

Activate the ESD input

No. 456

Aborted by the user

Description

The test was aborted by the user

Trouble shooting

This error can be solved by:

•

Perform a new FST

Содержание IDC24-A











































































Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды

Val Controls IDC24-A, Руководство пользователя

Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды