manualshive.com logo in svg

Val Controls IDC24-A, Руководство пользователя

Поделиться
Скачать
Val Controls IDC24-A Скачать руководство пользователя страница 63

 
 

 

DID-UM-002 

Val Controls A/S 

•

 Limfjordsvej 3 

•

 DK-6715 Esbjerg N 

•

 Tel. +45 7547 0600 

[email protected] 

•

 www.valcontrols.com 

Revision: 10 

 

 

63/74 

No. 511 

SOT error: Timeout 

Description 
 

Position based SOT: 
Breakaway not detected within the max time 
 
Pressure based SOT: 
The pressure did not drop within max time 
 

Trouble shooting 
 

The solenoid valve did not react 
 
This error can be solved by: 

•

 

Resolve the mechanical problem 

•

 

Increase max time 

•

 

Increase Pressure deadband 

 

 

No. 512 

SOT error: Breakaway, no pressure drop 

Description 
 

Breakaway is detected but there is no pressure drop 

Trouble shooting 
 

This error is generated when the pressure transmitter is not sensing the 
pressure drop. 
 
This error can be solved by: 

•

 

Check pressure transmitter 

•

 

Decrease Pressure deadband 

 

 

No. 513 

SOT error: Total timeout 

Description 
 

Position based SOT: 
The valve did not open within the SOT total timeout 
 
Pressure based SOT: 
The pressure did not reach the start pressure within the SOT total timeout 
 

Trouble shooting 
 

This error can be caused by: 

•

 

No supply pressure 

•

 

The valve is stuck 

•

 

The valve is moving slow 

•

 

The solenoid valve cannot be activated 

It can be solved by: 

•

 

Resolve the mechanical problem 

•

 

Increase SOT total timeout value 

 

Содержание IDC24-A











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды