manualshive.com logo in svg

Val Controls IDC24-A, Руководство пользователя

Поделиться
Скачать
Val Controls IDC24-A Скачать руководство пользователя страница 30

 
 

 

DID-UM-002 

Val Controls A/S 

•

 Limfjordsvej 3 

•

 DK-6715 Esbjerg N 

•

 Tel. +45 7547 0600 

[email protected] 

•

 www.valcontrols.com 

Revision: 10 

 

 

30/74 

8

 

Test errors 

8.1

 

Partial stroke errors (401 to 419) 

 

No. 401 

PST start condition: Not at operational 

Description 
 

The valve is not at the operational position 
 
The valve must be at the operational position to perform a partial stroke. All 
measured times and pressures depends on that the valve is at the end position. 
 

Trouble shooting 
 

This error can be solved by 

•

 

Make sure the valve is at the operational position 

•

 

Perform an endpoint calibration. 

•

 

Increase the partial stroke position deadband 

 

 

No. 402 

PST start condition: Low start pressure 

Description 
 

The measured pressure is below Start pressure low 
 

Trouble shooting 
 

This error can be solved by: 

•

 

Increase the pressure in the hydraulic/pneumatic system 

•

 

Decrease Start pressure low 
 

 

No. 403 

PST start condition: High start pressure 

Description 
 

The measured pressure is above Start pressure high 
 

Trouble shooting 
 

This error can be solved by: 

•

 

Decrease the pressure in the hydraulic/pneumatic system 

•

 

Increase Start pressure high 

 

No. 404 

PST start condition: In ESD mode 

Description 
 

Emergency shutdown is detected 
 

Trouble shooting 
 

This error can be solved by: 

•

 

Activate the ESD input 

 

Содержание IDC24-A











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды