Val Controls IDC24-A Скачать руководство пользователя страница 62

Страница: 62 / 74

DID-UM-002

Val Controls A/S

•

Limfjordsvej 3

•

DK-6715 Esbjerg N

•

Tel. +45 7547 0600

[email protected]

•

www.valcontrols.com

Revision: 10

62/74

8.5

Solenoid valve test errors (501 to 514)

No. 501

SOT start condition: Not at operational

Description

The valve is not at the operational position

Trouble shooting

This error can be solved by

•

Make sure the valve is at the operational position

•

Perform an endpoint calibration.

•

Increase the solenoid test position deadband

No. 502

SOT start condition: Low start pressure

Description

The measured pressure is below Start pressure low

Trouble shooting

This error can be solved by:

•

Increase the pressure in the system

•

Decrease the Start pressure low

No. 503

SOT start condition: High start pressure

Description

The measured pressure is above Start pressure high

Trouble shooting

This error can be solved by:

•

Decrease the pressure in the system

•

Increase Start pressure high

No. 504

SOT start condition: In ESD mode

Description

Emergency shutdown is detected

Trouble shooting

This error can be solved by:

•

Activate the ESD input

No. 506

Aborted by the user

Description

The test was aborted by the user

Trouble shooting

This error can be solved by:

•

Perform a new SOT

Содержание IDC24-A











































































Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды

Val Controls IDC24-A, Руководство пользователя

Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды