Vaisala HUMICAP HMW90 SERIES Скачать руководство пользователя

Страница: 25 / 110

Chapter 3 ________________________________________________________________ Installation

VAISALA ________________________________________________________________________ 23

If you change the position of DIP switch 8, note the following:

- When changing from

Custom

DIP

: Current custom settings are

overwritten by the settings from the DIP switches at next power up.

Settings that do not have DIP switches remain unchanged, except for

display layout (

DSEL

command) that is set to default.

- When changing from

DIP

Custom

: The DIP settings that were

used when the power was last on are carried over to the custom

settings at next power up.

Relay Configuration in DIP Mode

NOTE

Relay is included on HMW93 and TMW93 transmitters only.

When the transmitter is configured using DIP switches, the functioning

of the relay is configured by DIP switch 5 and the rotary switch on the

component board:

- DIP switch 5 determines if the relay is closed above or below the

setpoint.

- The position of the rotary switch determines the setpoint according to

the table below.

Table 5

Rotary Switch and Relay Setpoint

Rotary Switch Position Setpoint on HMW93

Setpoint on TMW93

5 %RH

0 °C (32 °F)

10 %RH

5 °C (41 °F)

20 %RH

10 °C (50 °F)

30 %RH

15 °C (59 °F)

40 %RH

20 °C (68 °F)

50 %RH

25 °C (77 °F)

60 %RH

30 °C (86 °F)

70 %RH

35 °C (95 °F)

80 %RH

40 °C (104 °F)

90 %RH

45 °C (113 °F)

NOTE

The rotary switch only has 10 positions. Do not turn the switch so that it

is between two positions.

Содержание HUMICAP HMW90 SERIES















































































































Результаты поиска

Содержание HUMICAP HMW90 SERIES

Отзывы:

Похожие инструкции для HUMICAP HMW90 SERIES

Бренды по названию

Популярные бренды

Vaisala HUMICAP HMW90 SERIES, Руководство пользователя

Результаты поиска

Содержание HUMICAP HMW90 SERIES

Отзывы:

Похожие инструкции для HUMICAP HMW90 SERIES

Бренды по названию

Популярные бренды