background image

User's Guide _______________________________________________________________________  

90 ___________________________________________________________________ M211399EN-F 

Device Object 

Table 19 below describes the properties of the device object. Note the 

following: 

-  Writable means writable via BACnet 

Max_Master

 and 

Max_Info_Frames

 are required in a Master device. 

UV

 = Configured at Vaisala factory to a unique value. See additional 

information after the table. 

Table 19 

Device Object Properties 

Property 

Data type 

(Application Type) 

Writable 

(Conforma

nce Code) 

Value or Initial Value 

Persistence 

Object_Identifier 

BACnetObjectIdentifier  Y (R) 

02 00 00 00 (hex) 

Object Type = 8,  

Instance = xxxxxxx 

UV

 

Nonvolatile 

Object_Name 

CharacterString[50] 

Y (R) 

"HMW90_Yxxxxxxx" 

UV

  Nonvolatile 

Object_Type 

BACnetObjectType 

(ENUMERATED) 

N (R) 

8 (Device Object) 

Fixed 

System_Status 

BACnetDeviceStatus 

(ENUMERATED) 

N (R) 

0 (Operational) 

Volatile 

Vendor_Name 

Character String 

N (R) 

"Vaisala Oyj" 

Fixed 

Vendor_Identifier 

Unsigned16 

N (R) 

339 

Fixed 

Model_Name 

CharacterString 

N (R) 

"HMW95" 

Nonvolatile 

Firmware_Revision 

CharacterString 

N (R) 

X.X.X.X (BACnet 

interface) 

Fixed 

Application_Software

_Revision 

CharacterString 

N (R) 

X.X.X.X 

Fixed 

Location 

Character String[50] 

Y (O) 

“Location”  

Nonvolatile 

Description 

Character String[50] 

Y (O) 

“Description”  

Nonvolatile 

Protocol_Version 

Unsigned 

N (R) 

Fixed 

Protocol_Revision 

Unsigned 

N (R) 

Fixed 

Protocol_Services 

BACnetProtocolServic

es Supported (BIT 

STRING) 

N (R) 

Read Property 

Read Property Multiple 

Write Property 

Device Communication 

Control 

Reinitialize Device 

Who-Is  

Who-Has  

Fixed 

Protocol_Object_Typ

es_Supported 

BACnetObjectTypesSu

pported (BIT STRING) 

N (R) 

Analog Input 

Analog Value 

Device 

Fixed 

Содержание HUMICAP HMW90 SERIES















































































































Отзывы: