Vaisala DMP248 Скачать руководство пользователя страница 65

Страница: 65 / 141

HAPTER

6 ______________________________________________

CALIBRATION

AND ADJUSTMENT

AISALA

_________________________________________________________________________ 61

•

Connect an ammeter/voltmeter to the analogue outputs (connector
X2). Give command

¡¡l¡

. At the first calibration point the

LED on the left flashes; adjust the first point (offset) with the
arrow switches to the same reading with the reference and press
ENT switch.

•

After adjusting the offset point and pressing ENT the second LED
from left flashes. Press ENT without changing the output value.

Two-point temperature calibration and adjustement

Using serial commands

•

Leave the reference instrument and the transmitter for at least 4
hours in the same space so that their temperatures have time to
equalize. Remove the filter cap prior to calibration.

Disconnect the security lock jumper
before turning the transmitter on!

•

Check the transmitter against the reference.

•

Give command CT <cr>, enter the first point value and press <cr>:

>CT <cr>
T : xx.x Ref1 ? yy.y <cr>
Press any key when ready

•

If you want to see how the sensor stabilizes to the reference
temperature, enter c <cr> instead of the first reference:

T : 0.90 Ref1 ? c <cr>
T : 0.55 Ref1 ? c <cr>
T : 0.55 Ref1 ? 0.0 <cr>
Press any key when ready...

•

Change the temperature and again check the transmitter against
the reference.

•

Check that the reading corresponds with the reading of the
reference instrument. If not, adjust the second point.

•

Press any key, enter the second point value and press <cr>.

T : xx.x Ref2 ? yy.y <cr>

All manuals and user guides at all-guides.com

Содержание DMP248














































































































































Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды

Vaisala DMP248, Руководство по эксплуатации

Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды