manualshive.com logo in svg

Vaisala DMP248, Руководство по эксплуатации

Поделиться
Скачать
Vaisala DMP248 Скачать руководство пользователя страница 62

OPERATING MANUAL _______________________________________________________________

58_____________________________________________________________________M210492

EN

-

A

•

 

If necessary, change the second point reading with the arrow keys
and press ENT.

Using LED commands

•

 

Leave the calibrator and the transmitter for at least 4 hours in the
same space so that their temperatures have time to equalize.
Remove the filter cap on the transmitter.

Disconnect the security lock jumper
before turning the transmitter on!

•

 

Place the sensor head in the calibration hole of the LiCl bottle (dry
end reference) in the humidity calibrator.

•

 

Connect an ammeter/voltmeter to the analogue outputs (connector
X2). Give command 

¡¡¡l

. At the first calibration point the

LED on the left flashes; adjust the first point (offset) with the
arrow switches to the value given in the calibration table and press
ENT switch.

•

 

Place the sensor head in the calibration hole of the NaCl bottle
(wet end reference) in the humidity calibrator.

•

 

Wait for 30 minutes.

•

 

Check that the reading corresponds within the desired accuracy to
that given in the calibration table. If not, adjust the second point
with the arrow switches to the correct value and press ENT. At the
second calibration point the second LED from the left flashes.

All manuals and user guides at all-guides.com

Содержание DMP248














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды