manualshive.com logo in svg

Vaisala DMP248, Руководство по эксплуатации

Поделиться
Скачать
Vaisala DMP248 Скачать руководство пользователя страница 42

OPERATING MANUAL _______________________________________________________________

38_____________________________________________________________________M210492

EN

-

A

NOTE

If the process pressure differs from the normal ambient pressure, the
value has to be entered in the transmitter memory to ensure the best
possible measurement accuracy. The pressure setting is used for
pressure compensation of the DMP248 transmitter.

Forced auto-calibration

•

 

Select 

More

 in the main menu and then again 

More

 in the second

More menu. Select 

Dry cal

 and then 

Calibration

•

 

Select 

More

 in the main menu and then again 

More

 in the second

More menu. Select 

Dry cal

 and then 

Calibration

. The following is

displayed:

Calibration...

press any key to abort

•

 

If you press any key, the calibration is interrupted. If no key is
pressed, the calibration takes place immediately. The text above is
displayed during the calibration. If the process is unstable (see
Chapter  Auto-calibration) or relative humidity is over 10%, the
calibration is not performed. The text above is only shortly
displayed and the display returns to the measuring mode. The
calibration is not performed again even if the maximum correction
is exceeded.

Analogue output commands

Selecting the output (mA/V)

Disconnect the security lock jumper!

•

 

Select 

Mode

 in the main menu and 

Analog outputs

 in the Mode

menu:

•

 

Select 

Mode ( mA / V )

. The current settings for channel 1 are

displayed:

All manuals and user guides at all-guides.com

Содержание DMP248














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды