Vaisala DMP248 Скачать руководство пользователя страница 61

Страница: 61 / 141

HAPTER

6 ______________________________________________

CALIBRATION

AND ADJUSTMENT

AISALA

_________________________________________________________________________ 57

RH : 11.5 Ref1 ? 11.3 <cr>
Press any key when ready...

•

Place the sensor head in the calibration hole of the NaCl bottle
(wet end reference) in the humidity calibrator.

•

Wait for 30 minutes.

•

Press any key and enter the second point value and press <cr>.

RH : xx.x Ref2 ? yy.y <cr>

•

The stabilization of the sensor can be monitored here as well by
entering c <cr> instead of the reference value.

Using display/keypad commands

•

Leave the calibrator and the transmitter for at least 4 hours in the
same space so that their temperatures have time to equalize.
Remove the filter cap on the transmitter.

Disconnect the security lock jumper
before turning the transmitter on!

•

Place the sensor head in the calibration hole of the LiCl bottle (dry
end reference) in the humidity calibrator.

•

Select

Cali

in the main menu and then

; select

Not changed

and then two-point calibration

RH 2 point cal

. Change the first

point reading with the arrow keys to correspond the reference
humidity and press ENT; pressing an arrow once changes the
reading by 0.05 %RH.

•

Place the sensor head in the calibration hole of the NaCl bottle
(wet end reference) in the humidity calibrator.

•

Wait for 30 minutes.

All manuals and user guides at all-guides.com

all-guides.com

Содержание DMP248














































































































































Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды

Vaisala DMP248, Руководство по эксплуатации

Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды