manualshive.com logo in svg

Vaisala DMP248, Руководство по эксплуатации

Поделиться
Скачать
Vaisala DMP248 Скачать руководство пользователя страница 10

OPERATING MANUAL _______________________________________________________________

6______________________________________________________________________M210492

EN

-

A

F

IGURE 

2-2

The DRYCAP

 sensor mounted on a DMP248 probe.

Note that the auto-calibration takes place only if the DMP248 is used
in ambient humidities below 10 %RH (dewpoint below -12 

°

C at 20 

°

C) and at ambient temperature 0...+80 °C.

Use in high pressure

If the process pressure differs from the normal ambient pressure, the
value has to be entered in the transmitter memory to ensure the best
possible measurement accuracy. The pressure setting is used for
pressure compensation of the DMP248 transmitter. Note that although
dewpoint is a pressure dependent parameter, this setting cannot be
used for calculating dewpoints in different pressures. The probe
should be installed to a place with pressure equal to that of the process
in order to ensure the most reliable measurement. For converting
pressure units, see Appendix 8.

NOTE

The probe can be installed in the process through the ball valve
assembly provided that the process pressure is less than 10 bars. This
way, the process does not have to be shut down when installing or
removing the probe. However, if the probe is not removed from the
process as such (e.g. the process is shut down first), the process
pressure can be max. 20 bars.

All manuals and user guides at all-guides.com

Содержание DMP248














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды