manualshive.com logo in svg

Vaisala DMP248, Руководство по эксплуатации

Поделиться
Скачать
Vaisala DMP248 Скачать руководство пользователя страница 116

A

PPENDIX 

3_________________________________________________________________________

112____________________________________________________________________M210492

EN

-

A

>send 22
RH= 24.4 %RH T= 29.1 'C

•

Disconnect the terminal.

•

Check that the jumpers in connector X4 are in the right places.

X4

X4

X1

X2

•

Remount the RS 485/422 serial module.

•

Close the cover.

•

Repeat this setting procedure with each transmitter.

•

When all transmitters on the network have been configured,
switch them off.

Checking the serial port network operation

Normally measurement readings are asked when the transmitter is in
POLL mode; then the command must include the address of the
transmitter. If the settings of the transmitter need to be changed, the
transmitter is switched to STOP mode with command OPEN;
commands can then be given without address. When the line to the
transmitter is closed, it returns to POLL mode.

STOP mode

Open the line to the transmitter:

open 22<cr>
DMP 22 line opened for operator commands

Transmitter no. 22 is now temporarily set to STOP mode; it accepts
commands sent without address until CLOSE command is given.
Individual settings can now be easily modified. Do not open more
than one line at a time.

All manuals and user guides at all-guides.com

all-guides.com

Содержание DMP248














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды