manualshive.com logo in svg

Vaisala DMP248, Руководство по эксплуатации

Поделиться
Скачать
Vaisala DMP248 Скачать руководство пользователя страница 138

A

PPENDIX 

7_________________________________________________________________________

134____________________________________________________________________M210492

EN

-

A

Setting and activating the outputs using an RS line

Disconnect the security lock jumper!

ALARM <cr>

or

ALARM n ON <cr>

where n = channel number (1 or 2)

The currently valid settings of the alarm output unit can be checked
with command ALARM:

>alarm<cr>
Ch1

RH

LO

OFF

  0.00

0.00 %RH

Ch2

RH

HI

OFF

100.00

0.00 %RH

>

This is an example of the factory setting (both alarm outputs are in
OFF mode, i.e. not in use). The settings can be changed with
command ALARM:

>alarm

1

Td

HI

-20

5

Ch1

Td

HI

OFF

-20.00

5.00 'C

Ch2

RH

HI

OFF

100.00

0.00 %RH

>

When giving this command, first enter the channel number i.e. the
number of the alarm output you wish to use (1 or 2). Then select the
quantity you wish to have on that channel (Td, ppm, RH or T). The
third parameter (HI/LO) determines, whether the alarm is activated
when the setpoint value is exceeded (HI) or not reached (LO). The
fourth parameter is the actual setpoint value, which activates the
alarm. The last parameter is the hysteresis value; it indicates how
much the measured value has to exceed or go below the setpoint
before the alarm is deactivated. If the third parameter is HI, the alarm
is deactivated when the measured value goes below the setpoint with
the chosen hysteresis value. If the parameter is LO, the alarm is
deactivated when the measured value exceeds the setpoint with the
chosen hysteresis value.

All manuals and user guides at all-guides.com

Содержание DMP248














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды