Vaisala DMP248 Скачать руководство пользователя страница 136

Страница: 136 / 141

PPENDIX

7_________________________________________________________________________

132____________________________________________________________________M210492

side of the module if the mains power is in use. Attach the ribbon
cable from X3 of the alarm unit to the X16 on the main board of the
transmitter.

NOTE

NO jumper in connector X4 during normal operation.

When one alarm unit relay is on, the corresponding LED is lit.

signal cable gland

X16

ribbon cable

M3 screws (4 pcs) for mounting
(prefix with fibre washers)

M4 screw and washer for
protective ground terminal

replace the plastic plug with cable
gland for ¢7...12 mm cable

cable: strip wires only 5 mm; use
crimped terminal for ground wire
if stranded wire is used

probe cable gland

arrange signal cable wires so
that they do not reach bare AC
wires when the cover is closed

Prefix the fastening screws with fiber washers for mounting the unit to
the box.

NOTE

The alarm unit cannot be used with the power supply unit
HMP230PW.

WARNING

Do not detach the alarm unit from the transmitter when the power is
on.

WARNING

Do not connect the mains power to alarm unit without grounding the
transmitter.

All manuals and user guides at all-guides.com

all-guides.com

Содержание DMP248














































































































































Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды

Vaisala DMP248, Руководство по эксплуатации

Результаты поиска

Содержание DMP248

Отзывы:

Бренды по названию

Популярные бренды