Upright ab62 Скачать руководство пользователя страница 39

Страница: 39 / 146

AB62 Work Platform - European

3-21

AINTENANCE

Section

3.13

Figure 3-24: Rotary Manifold

3.13 R

OTARY

ANIFOLD

EMOVAL

1. Mark and tag all hoses.
2. Remove all hoses from Rotary Manifold.
3. Remove Rotary Manifold from the machine.

NOTE: Provide a clean work area for this opera-

tion, and observe clean assembly practices.
Seals and O-rings are highly sensitive to con-
tamination that may not be visible to the naked
eye.

Disassembly

1. Remove Retaining Rings from each end of

Rotary Manifold.

2. Carefully slide body out of housing.
3. Remove seal kit components (O-rings, seals, and

retaining rings).

4. Thoroughly clean all parts with solvent. Rinse the

inside of the tube and allow to drain. A high pres-
sure rinse and wipe with a lint free rag is prefera-
ble.

5. Inspect the body and housing for scratches, pits,

or polishing. Check seal grooves and sealing sur-
faces. Scratches or pits deep enough to catch the
fingernail are unacceptable, replace the manifold.

Assembly

NOTE: Torque all hardware and fittings to torques

listed on pages 3-22 and 3-23 unless otherwise
specified.

1. Lubricate all seals with clean hydraulic oil prior to

assembly.

2. Install new seals on body and housing.
3. Carefully slide body into housing.
4. Reinstall O-rings and retaining rings.

Installation

1. Installation is reverse of removal.
2. Replenish hydraulic fluid in tank.
3. Run hydraulic system for several minutes to

remove air from hydraulic lines. Cycle cylinders
for each boom function.

4. Rotate turret completely.
5. Check Rotary Manifold for leaks. Check that all

boom functions are operating properly.

Содержание ab62



















































































































































Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды

Upright ab62, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды