Upright ab62 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 146

background image

2-6

AB62 Work Platform - European

M

ACHINE

P

REPARATION

& O

PERATION

Section

2.4

1. Set the function speed control dial to the desired

setting. Rotate the dial clockwise to increase
speed, counterclockwise to decrease.

2. While depressing the foot switch, push the riser

control lever forward to elevate the riser, rearward
to lower the riser. Release the control lever to
stop elevating/lowering.

1. Set the function speed control dial to the desired

setting. Rotate the dial clockwise to increase
speed, counterclockwise to decrease. If you are
not sure what speed to use, start out slow; the
speed can be varied while operating the function.

2. While depressing the foot switch, push the upper

boom control lever forward to elevate the upper
boom, rearward to lower the upper boom.
Release the control lever to stop elevating/
lowering.

1. Set the function speed control dial to the desired

setting. Rotate the dial clockwise to increase
speed, counterclockwise to decrease. If you are
not sure what speed to use, start out slow; the
speed can be varied while operating the function.

2. While depressing the foot switch, push the boom

extension control lever rearward to extend the
boom, forward to retract the boom. Release the
control lever to stop extending/retracting.

1. Set the function speed control dial to the desired

setting. Rotate the dial clockwise to increase
speed, counterclockwise to decrease. If you are

not sure what speed to use, start out slow; the
speed can be varied while operating the function.

2. While depressing the foot switch, push the jib

control lever forward to elevate the jib, rearward
to lower the jib. Release the control lever to stop
elevating/lowering.

1. While depressing the foot switch, push the plat-

form rotation control lever right to go counter-
clockwise and left to go clockwise. Release the
lever to stop rotation.

Emergency Operation

In the event of powered function failure, the elevating
assembly may be operated by using the Emergency
Power Unit. Hold in the Emergency Power button and
operate the Lowering Controls as normal.

Emergency Towing

Perform the following only when the machine will not
operate under its own power and it is necessary to
move the machine or when winching onto a trailer for
transportation
1. Insure that the platform is fully lowered, and that

the turret is rotated so that the platform is to the
rear of the machine.

2. Attach chain/cable of sufficient strength for towing

the machine to front or rear tie down lugs.

3. Refer to Figure 2-6 and disengage all four drive

hubs. Remove two screws and center cap. Re-
install center cap in the opposite direction.

NOTE: When hubs are disengaged, the brakes

are ineffective. The machine will roll freely.

Elevating the Riser

Elevating the Upper Boom

Extending the Upper Boom

Elevating the Jib

W A R N I N G

!

!

NEVER climb down the elevating assembly. If
controls do not respond, ask someone on the
ground to lower the boom manually.

W A R N I N G

!

!

Chock

wheels

before

disengaging

hubs.

Machine may roll.

Rotating the Platform

«
...
14
15
16
17
18
...
»

Содержание ab62



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ab62

Бренд: Happ Страницы: 49

EcoTouch Ai1 Geo

Бренд: WATERKOTTE Страницы: 60

Бренд: WaterCop Страницы: 4

Бренд: V2 Страницы: 48

Бренд: Vulcan-Hart Страницы: 28

Бренд: Migatronic Страницы: 28

Бренд: National Instruments Страницы: 18

Бренд: HEEVE Страницы: 8

Genie GS-2669 DC

Бренд: Terex Страницы: 147

Бренд: ZEBSBOARDS Страницы: 9

Бренд: Miller Electric Страницы: 18

Бренд: Magneti Marelli Страницы: 44

Бренд: R-Tech Страницы: 23

Бренд: Eastwood Страницы: 12

Бренд: Carel Страницы: 2

Бренд: Norco Страницы: 2

UltraTwin FreeSpan

Бренд: Liko Страницы: 10

Бренд: Ravaglioli Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды