Upright ab62 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 146

background image

3-12

AB62 Work Platform - European

M

AINTENANCE

Section

3.10

3.10 T

ORQUE

H

UBS

NOTE: Change fluid in torque hubs after the first

50 hours of operation. Change every 1000
hours thereafter.

Changing Fluid

NOTE: It is not necessary to remove torque hub

to change fluid.

1. Raise the axle using an eight-ton hydraulic jack.

Place eight ton-jack stands under each end of the
axle.

2. Remove wheel and rotate torque hub so drain

plug on side is at bottom of hub.

3. Remove drain plugs at bottom of hub and front

cover, and drain oil from unit.

4. Rotate hub so plug opening in front cover is

slightly above half full position and side plug
opening is at the top.

5. Fill unit with 90 wt. gear oil until oil comes out

front plug opening (torque hub must be 1/2 full).

6. Replace plugs.
7. Install wheel and lower machine to the ground.

Torque Hub Removal

1. Park the work platform on firm level, ground and

block the wheels to prevent the work platform
from rolling.

2. Disconnect battery negative terminal.
3. Loosen the wheel lug nuts on the torque hub to

be removed.

4. Raise the axle of the work platform using an

eight- ton jack.

5. Position two eight-ton jack stands under the axle

to prevent the work platform from falling if the jack
fails.

6. Remove the wheel nuts and wheel.
7. Disconnect hydraulic brake line from brake.

8. Mark and remove hoses from drive motor.
9. Remove mounting bolts from drive motor.
10. Separate drive motor from brake. Discard gasket.

11. Separate brake from torque hub. Discard gasket.
12. Remove 1/2-20 nuts and washers from torque

hub.

13. Remove torque hub.

Installation

NOTE: Torque all hardware to torques listed on

pages 3-22 and 3-23 unless otherwise speci-
fied.

1. Install the torque hub using hardware previously

removed.

2. Using SAE 90W weight gear lube, fill the torque

hub. Torque hub must be half full.

3. Install new gasket and brake.
4. Install new gasket and drive motor.
5. Secure assembly using washers and bolts.
6. Connect hydraulic brake lines.
7. Connect hoses to drive motor.
8.Install wheels.Torque lug nuts to 257Nm

(190 ft/lbs).

9. Bleed brake lines if necessary.
10. Remove jack stands and lower rear end.
11. Connect battery terminal.
12. Operate machine and check for proper operation

of torque hub. Check function of brake.

Figure 3-14: Torque Hub Assembly

C A U T I O N

!

!

Clean all fittings before disconnecting the hose
assemblies.
Plug all port holes and hose assemblies IMME-
DIATELY to prevent contamination from dust
and debris.

FRONT

REAR

«
...
28
29
30
31
32
...
»

Содержание ab62



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ab62

Бренд: Rain Bird Страницы: 48

Бренд: TAC Страницы: 4

Бренд: Geberit Страницы: 49

Бренд: National Comfort Products Страницы: 28

Бренд: Orion Welders Страницы: 51

EtherCAT Compact67 Slim

Бренд: elco Страницы: 28

Бренд: Aichi Страницы: 54

SITALI CXOM 180

Бренд: Olimpia splendid Страницы: 32

Бренд: Zepro Страницы: 64

Бренд: gala gar Страницы: 42

MoveAround MA50

Бренд: Safelift Страницы: 20

Бренд: Miller Electric Страницы: 40

Бренд: M-system Страницы: 5

Бренд: GYS Страницы: 60

Бренд: GYS Страницы: 24

Бренд: B-TEC Страницы: 33

e-Sense Actilume

Бренд: Fagerhult Страницы: 9

ST 44 Series Wire Feeder

Бренд: Miller Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды