Upright ab62 Скачать руководство пользователя страница 23

Страница: 23 / 146

AB62 Work Platform - European

3-5

AINTENANCE

Section

3.4

3.4 S

UPPORTING

LEVATING

SSEMBLY

IGURE

3-6)

Installation

1. Park the work platform on a firm, level surface.
2. Fully retract upper boom.
3. Verify that the platform emergency stop switch is

ON.

4. Turn platform/chassis switch to CHASSIS.
5. Using the Boom Raise/Lower Switch, elevate the

boom.

6. Use a brace (figure 3-6) with a minimum capacity

of two tons, to support the elevating assembly.

7. Using the Boom Raise/Lower Switch gradually

lower the elevating assembly until the brace is
supporting the elevating assembly as shown in
figure 3-7.

Removal

1. Using the Boom Raise/Lower Switch, gradually

raise the platform until boom is free of support.

2. Remove support.
3. Using the Boom Raise/Lower Switch, completely

lower the platform.

Figure 3-6: Supporting Elevating Assembly

Figure 3-7: Elevating Assembly Brace

W A R N I N G

Never perform service on the work platform in
the elevating assembly area while the platform
is elevated without first blocking the elevating
assembly.
DO NOT stand in the elevating assembly area
while deploying or storing brace.

Содержание ab62



















































































































































Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды

Upright ab62, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды