Upright ab62 Скачать руководство пользователя страница 27

Страница: 27 / 146

AB62 Work Platform - European

3-9

AINTENANCE

Section

3.8

3.8 H

YDRAULIC

ANIFOLD

IGURE

3-14)

It is not necessary to remove the manifold to perform
all maintenance procedures. Prior to performing
maintenance, determine if the manifold needs to be
removed.

Removal

1. Disconnect the battery.
2. Tag and disconnect the solenoid valve leads from

the terminal strip.

3. Tag, disconnect, and plug hydraulic hoses.
4. Remove the bolts that hold the manifold to the

mounting bracket.

5. Remove the manifold block.

Disassembly

NOTE: Mark all components as they are removed

so as not to confuse their location during
assembly. Refer to Figure 3-14 often to aid in
disassembly and assembly.

1. Remove coils from solenoid valves.
2. Remove spool valve cover and spool valve.
3. Remove solenoid valves, lift relief valve, counter-

balance valves and divider combiner valve.

4. Remove fittings, plugs, springs, balls, and ori-

fices.

Cleaning and Inspection

1. Wash the manifold in cleaning solvent to remove

built-up contaminants, then blow out all passages
with clean compressed air.

2. Inspect the manifold for cracks, thread damage

and scoring where O-rings seal against internal
and external surfaces.

3. Wash and dry each component and check for

thread damage, torn or cracked O-rings, and
proper operation.

4. Replace parts and O-rings found unserviceable.

Assembly

NOTE: Lubricate all O-rings before installation to

prevent damage to O-rings. Seat all balls in
manifold block by lightly tapping on the ball
with a brass drift punch.

1. Install fittings, plugs, springs, balls, and orifices.

Use one drop of Locktite #242 on each screw-in
orifice.

2. Install solenoid valves, lift relief valve, counterbal-

ance valves, divider combiner valve, and spool
valve.

Installation

1. Attach manifold assembly to mounting plate with

bolts.

2. Connect solenoid leads to terminal strip (as previ-

ously tagged).

3. Connect hydraulic hoses. Be certain to tighten

hoses to manifold.

4. Reconnect the battery.
5. Operate each hydraulic function and check for

proper operation and leaks.

6. Adjust lift relief and counterbalance valve pres-

sures according to instructions in Section 3-10.

Содержание ab62



















































































































































Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды

Upright ab62, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды