Upright ab62 Скачать руководство пользователя страница 20

Страница: 20 / 146

3-2

AB62 Work Platform - European

AINTENANCE

Section

3.2

UpRight Connectors

Figure 3-3: Plugs and Receptacles, UpRight Connectors

Deutsch connectors are designed so that connector
parts, contacts or electrical cables may be replaced
without replacing the entire connector.

Male Connector (Plug)

1. Disconnect the male connector (plug) from the

female connector (receptacle).

2. Using the flat end of the Removal Tool (or flat

blade screwdriver), pry the Locking Wedge from
the Male Connector. Care should be taken that
the Silicon Gasket is not damaged during this
procedure.

3. Check all parts for damage. Replace all parts

which are damaged or worn.

4. Replace or recrimp the wires and contacts. Refer

to “Crimping” procedure.

Female Connector (Receptacle)

1. Disconnect the male connector (plug) from the

female connector (receptacle).

2. Using the notched end of the Removal Tool (or a

wire hook), pull the Locking Wedge from the
Female Connector.

3. Check all parts for damage. Replace all parts

which are damaged or worn.

4. Replace or recrimp the wires and contacts. Refer

to “Crimping” procedure.

Releasing Locking Fingers

Figure 3-4: Locking Finger, UpRight Connector

1. The Locking Fingers can be released following

the removal of the Locking Wedge of either the
male or female connector.

2. Use the removal tool (or flat blade screwdriver) to

push the Locking Fingers aside. This will release
the grip on the contact.

3. Pull the wire and contact out of the connector.

Crimping

Note: Complete crimping instructions are

included in each Field Kit.

1. Strip 1/4” (6 mm) from the wire.
2. Insert the contact into the crimping tool.
3. Insert the stripped wire into the contact. Copper

strands should be visible in the bleed hole of the
contact, and no copper strands should be loose
(outside) of the contact barrel.

4. Completely close the handles of the crimping

tool. Release the handles of the crimping tool and
remove the crimped contact.

Содержание ab62



















































































































































Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды

Upright ab62, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание ab62

Отзывы:

Похожие инструкции для ab62

Бренды по названию

Популярные бренды