Upright ab62 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 146

background image

3-6

AB62 Work Platform - European

M

AINTENANCE

Section

3.5

3.5 B

ATTERY

M

AINTENANCE

Battery Inspection and Cleaning

Check battery fluid level daily, especially if the work
platform is being used in a warm, dry climate. If
required, add distilled water ONLY. Use of tap water
will shorten battery life.
The battery should be inspected regularly for signs of
cracks in the case, electrolyte leakage and corrosion
of the terminals. Inspect cables for worn spots or
breaks in the insulation and for broken cable
terminals.
Clean the battery when it shows signs of corrosion at
the terminals or when electrolyte has overflowed dur-
ing charging. Use a baking soda solution to clean the
batteries, taking care not to get the solution inside
the cells. Rinse thoroughly with clean water. Clean
battery and cable contact surfaces to a bright metal
finish whenever a cable is removed.

Battery Charging

Charge battery as follows:
1. Check the fluid level. If the electrolyte level is

lower than 10mm (3/8 in) above the plates, add
clean, distilled water only.

2. Connect the charger plug to a properly grounded

outlet of the proper voltage and frequency.

3. Use a charger which turns off automatically when

the batteries are fully charged.

3.6 L

UBRICATION

Refer to Table 3-1 for the lubrication intervals and
Figures 3-8 and 3-9 for location of items that require
lubrication service. Refer to the appropriate sections
for lubrication information on the Steering Linkage,
Torque Hubs, Hydraulic Oil, Filter, and Engine Oil and
Filter.

Grease Fittings

Wipe each fitting before and after greasing. Using
multipurpose grease in a grease gun, pump the
grease into the fitting until grease just begins to
appear at the edges of the pivot. Wipe off any excess
grease.

Lubricating Turret Gears

Using a brush, apply open gear grease to the turret
gears (Figure 3-8).

W A R N I N G

!

!

Hazard of explosive gas mixture. Keep sparks,
flame and smoking material away from battery.
Always wear safety glasses when working with
batteries.
Battery fluid is highly corrosive. Thoroughly
rinse away any spilled fluid with clean water.

W A R N I N G

!

!

Charge the battery only in a well-ventilated
area.
Do not charge the battery when the work plat-
form is in an area containing sparks or flames.
Permanent damage will result if the battery is
not immediately recharged after discharging.
Never leave the charger unattended for more
than two days.
Never disconnect the cables from the battery
when the charger is operating.
Keep the charger dry.

«
...
22
23
24
25
26
...
»

Содержание ab62



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ab62

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: Linak Страницы: 33

Бренд: Clarke Страницы: 8

Бренд: M-system Страницы: 10

Бренд: ICP DAS USA Страницы: 6

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

Бренд: T&R Страницы: 12

Бренд: Quality Heating Страницы: 15

Бренд: Nußbaum Hebetechnik Страницы: 32

SR/ABITIGL ABITIG GRIP

Бренд: Abicor Binzel Страницы: 36

Бренд: iCONNECT Страницы: 20

Бренд: Air Liquide Страницы: 23

Reflex Wheel-X 50 050 0030

Бренд: Carson Страницы: 52

Бренд: Miller Страницы: 136

Бренд: progressive automations Страницы: 6

Бренд: ABB Страницы: 4

Бренд: Danfoss Страницы: 36

Бренд: SmartAccess Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды