Upright ab62 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 146

background image

2-4

AB62 Work Platform - European

M

ACHINE

P

REPARATION

& O

PERATION

Section

2.4

2.4 O

PERATION

Before operating the work platform ensure that:
Pre-operation and safety inspection has been com-
pleted, and any discrepancies have been corrected.
The operator has been thoroughly trained on the
operation of the machine.
The work area is clear of all obstructions, holes,
drop-offs, or persons in the route of travel.
The surface is capable of supporting wheel loads.

Refer to figures 2-1 and 2-2 for control locations.

At any time during operation, press the emergency
stop button to stop all functions in an emergency.

At any time during operation, press the service horn

button to sound an audible warning if necessary.

Figure 2-5: Typical Fall Restraint Anchorage Point

From the Lower Controls

1. From the platform controls, turn the key switch

on.

2. Turn the chassis key switch to CHASSIS position.
3. Press the start button to crank the engine.

Release when the engine starts.

4. For diesel machines: Turn key to ON position and

wait for glow plug light to go off. Start engine.

From the Platform Controls

1. Turn the chassis key switch to platform controls.
2. Turn the platform switch fully clockwise to crank

the engine. Release when engine starts.

3. For diesel machines: Turn key to ON position and

wait for glow plug light to go off. When glow plug
light goes off, start engine.

With Boom Lowered

1. Turn chassis key switch to PLATFORM, and turn

on (turn clockwise) the chassis emergency stop
switch.

2. Mount the platform, close and latch the gate.
3. Attach approved fall restraint to designated plat-

form anchorage point. Attach only one fall
restraint to each point.

4. Start engine.
5. Check that the area around and above the work

platform is clear of obstructions, holes, drop-offs,
persons in the route of travel, and the surface is
capable of supporting wheel loads.

6. Depress the foot switch and move the drive con-

trol handle forward to travel forward and reverse
to travel in the reverse direction.

NOTE: When the boom is rotated to the front of

the chassis (steering wheels aft), directions of
travel and steering will be reversed. Observe
the color-coded arrows on the control panel
near the drive control handle and on the chas-
sis. They will indicate the direction of travel
when the drive control handle is moved

W A R N I N G

!

!

Always wear an approved fall restraint properly
attached to designated platform anchorage
point when driving or elevating the machine
(see figure 2-5). Attach only one fall restraint to
each anchorage point.

Emergency Stop

Service Horn

Starting the Engine

Driving

«
...
12
13
14
15
16
...
»

Содержание ab62



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ab62

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Balboa Страницы: 23

Бренд: Linak Страницы: 33

DigiRail-2R RS485

Бренд: Novus Страницы: 2

Бренд: Logic Страницы: 3

Бренд: Lincoln Electric Страницы: 39

Бренд: facelift Страницы: 8

Cruisair SMX II

Бренд: Taylor Made Environmental Страницы: 36

Бренд: Walter Страницы: 30

Бренд: Miller Страницы: 62

Бренд: SuperLogics Страницы: 24

Бренд: HALDER Страницы: 2

Бренд: National Instruments Страницы: 77

Бренд: MaxPro PROFESSIONAL Страницы: 69

Бренд: LSI-Robway Страницы: 95

Бренд: LSI-Robway Страницы: 97

Бренд: LSI-Robway Страницы: 109

Бренд: Aqua Control Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды