UNITED Nitrogen Pac SC-W страница 107 Скачать руководство пользователя

Страница: 107 / 112

LIMITED WARRANTY

TRUE ADVANCED PURGE

What Does This Warranty Cover?

This Limited Warranty covers all manufacturing defects in material and workmanship by

UNITED

Fire

Systems

new

TRUE ADVANCED PURGE

equipment.

How Long Does The Coverage Last?

This Limited Warranty lasts for eighteen (18) months from the date of shipment to the original purchaser.

What Will

UNITED

Fire Systems

Do?

UNITED

Fire Systems

will repair, replace, or refund the purchase price of, at its option, any defective

TRUE ADVANCED PURGE

equipment at no charge.

What Does This Warranty Not Cover?



Equipment that is not supplied by

UNITED

Fire Systems

is not covered.



Equipment that has not been installed, commissioned, operated, and maintained per the instructions
in the applicable

UNITED

Fire Systems

instruction manual is not covered.



Equipment that has been repaired, modified, or otherwise tampered with not in accordance with the
applicable

UNITED

Fire Systems

instruction manual is not covered.



Any problem that is caused by abuse, misuse, or an act of God (such as a flood) is not covered.



Transportation and shipping charges to return equipment to

UNITED

Fire Systems

or for

UNITED

Fire Systems

to return repaired or replacement equipment are not covered.



Consequential and incidental damages are not covered. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so this exclusion may not apply.

What Are The Customer’s Responsibilities?



Ensuring that the

UNITED

Fire Systems

equipment is installed, commissioned, operated, and

maintained per the instructions in the applicable

UNITED

Fire Systems

instruction manual.



Where applicable, ensuring that checklists supplied by

UNITED

Fire Systems

are properly used and

completed at the time of installation, commissioning, operation, and maintenance, and such
checklists are retained as records of proper completion.



Noting and recording the serial number(s) of

UNITED

Fire Systems

equipment.



Notifying

UNITED

Fire Systems

or a trained distributor of the need for service under this Limited

Warranty.

How Is Warranty Service Obtained?

If anything goes wrong with

UNITED

Fire Systems

equipment, contact:

Be prepared to supply the serial number(s) of the equipment requiring service,

and copies of the installation, commissioning, and maintenance checklists, as

applicable.

Page 1 of 2

UNITED

Fire Systems

Division of United Fire Protection Corporation

1 Mark Road

Kenilworth, NJ 07033 USA

Phone: 908-688-0300

Fax: 908-481-1131

https://unitedfiresystems.net/

= OR =

Your

Trained

Distributor

APPENDIX J - SC-W MANUAL

Содержание Nitrogen Pac SC-W

















































































































Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Похожие инструкции для Nitrogen Pac SC-W

Бренды по названию

Популярные бренды

UNITED Nitrogen Pac SC-W, Установка, наладка, обслуживание

Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Похожие инструкции для Nitrogen Pac SC-W

Бренды по названию

Популярные бренды