UNITED Nitrogen Pac SC-W страница 106 Скачать руководство пользователя

Страница: 106 / 112

LIMITED WARRANTY

NITROGEN-

PAC™ SC SERIES

Is This Limited Warranty Transferable?

If the

NITROGEN-

PAC™ SC SERIES

equipment is moved from one to another installation during the

time period of Limited Warranty coverage, the

NITROGEN-

PAC™ SC SERIES

equipment must be re-

commissioned by

UNITED

Fire Systems

or a trained distributor to be eligible for continuing coverage.

There will be a quoted charge for this re-commissioning.

Is This The Entire Warranty?

This Limited Warranty is the entire warranty given by

UNITED

Fire Systems

to the purchaser of new

NITROGEN-

PAC™ SC SERIES

equipment. Component warranties supplied by component

manufacturers to

UNITED

Fire Systems

that are valid for a longer period of time than the

UNITED

Fire

Systems

Limited Warranty may apply. Contact

UNITED

Fire Systems

for more information. There are no

other warranties expressed or implied, beyond those required by law.

How Do State and Federal Laws Apply?

This Limited Warranty grants specific legal rights per Federal law. There may also be other rights which
vary from state to state.

UFS-306A Rev. 2.00 Sep 2019

Page 2 of 2

APPENDIX H - SC-W MANUAL

Содержание Nitrogen Pac SC-W

















































































































Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Похожие инструкции для Nitrogen Pac SC-W

Бренды по названию

Популярные бренды

UNITED Nitrogen Pac SC-W, Установка, наладка, обслуживание

Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Похожие инструкции для Nitrogen Pac SC-W

Бренды по названию

Популярные бренды