UNITED Nitrogen Pac SC-W страница 87 Скачать руководство пользователя | Manualshive

Страница: 87 / 112

background image

Nitrogen / Air Maintenance Device for Fire Sprinkler Systems

Model

NAMD-1

UNITED

Fire Systems

Division of United Fire Protection Corporation
1 MARK ROAD
KENILWORTH, NJ 07033 USA
PHONE: 908-688-0300 FAX: 908-688-0218

unitedfiresystems.com

UFS-710 P/N 31-100013-002 Rev. 1.04 Aug 2020

INSTRUCTION SHEET

Page 1 of 4

This  document  is  provided  for informational purposes  only.   UNITED Fire  Systems  assumes  no  responsibility
for  the  product’s  suitability  for  a  particular  application.    The  product  must  be  properly  applied  to  perform  as
intended.  The information in this document is believed to be correct at the time of publication.  UNITED Fire
Systems reserves the right to add to, delete, or revise any information in this document without notice.

DESCRIPTION

The

UNITED

Fire Systems

Model NAMD-1

is an FM Approved device for controlling the nitrogen and / or air pressure in

preaction and dry-pipe fire sprinkler piping. The device is equipped with a high-precision pressure regulator capable of
providing accurate regulation over a wide range of inlet pressures and gas flows. This is especially important for sprinkler
corrosion inhibiting systems supplying nitrogen to the sprinkler system, since most nitrogen systems provide less gas flow that
a conventional air compressor.

SPECIFICATIONS

Model No.: NAMD-1

Material (other than regulator): Brass

Material (regulator body): Zinc

Inlet:

1/2” NPT Female

Outlet:

1/2” NPT Female

Inlet Pressure Range: 0-175 PSIG (0-1200 kPa gauge)

Outlet Pressure Range: 15-60 PSIG (100-410 kPa gauge)

Maximum Pressure: 175 PSIG (1200 kPa)

Temperature Range: -30°F to +150°F (-34°C to +65°C)

Dimensions (approx.):

9.75” L x 8.25” H (248 mm x 210 mm)

Weight (approx.): 7 lbs. (3.2 kg)

Figure 1

APPENDIX B - SC-W MANUAL

«
...
85
86
87
88
89
...
»

Содержание Nitrogen Pac SC-W

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Nitrogen Pac SC-W

Strada CN-GP50N

Бренд: Panasonic Страницы: 2

Strada CN-GP50N

Бренд: Panasonic Страницы: 7

Strada CN-GP50N

Бренд: Panasonic Страницы: 39

Бренд: Panasonic Страницы: 12

Бренд: 3M Страницы: 90

Бренд: TCL Страницы: 13

Бренд: Teac Страницы: 3

Бренд: BWT Страницы: 12

Бренд: Brita Страницы: 2

Бренд: National Instruments Страницы: 5

Бренд: Commax Страницы: 10

Бренд: M-E Страницы: 68

Бренд: urmet domus Страницы: 28

Бренд: Cary Audio Design Страницы: 41

Бренд: FARFISA INTERCOMS Страницы: 2

Бренд: Weh Страницы: 68

Бренд: Aqua Flo Страницы: 4

Бренд: Ebyte Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды