UNITED Nitrogen Pac SC-W Скачать руководство пользователя страница 79

Страница: 79 / 112

UNITED FIRE SYSTEMS -

NITROGEN-

PAC™

SC-W SERIES

INSTALLATION, COMMISSIONING, AND MAINTENANCE MANUAL

REVISION 1.01 MAR 2021 - P/N 30-NPWICM-000

6. TROUBLESHOOTING

IMPORTANT

All troubleshooting is to be performed by qualified personnel. Be aware of pressurized system components as some of
the troubleshooting procedures require system components to be pressurized.

Failure to do so can result in system

damage and/or personal injury.

SYMPTOM

INDICATION(S)

PROBLEM

SOLUTION

MANUAL

REFERENCE

Compressor does not

run

Green power indicator

OFF

ON / OFF Selector

Switch on Model SC-W

assembly is

OFF

Move ON / OFF

Selector Switch to

position

4.2

Power from panelboard

OFF

Check circuit

breaker

Green power indicator

Possible compressor

overheating

Allow compressor to

cool

Nitrogen purity in

sprinkler system not

increasing

Red “SYSTEM

BYPASSED

” indicator

Model SC-W assembly

is in Bypass mode

Verify position of

valves has been

restored to Nitrogen

position.

Figure 34

Red “SYSTEM

BYPASSED” indicator

OFF

Model SC-W assembly

may not be producing

nitrogen

Check nitrogen

purity at test port by

using Model NA-2

analyzer

5.2.1

Model SC-W assembly

is producing 98%

nitrogen when

checked with Model

NA-2 analyzer

Valve

on Model SC-W

assembly is

CLOSED

Open valve

Valve on Model PVA is

CLOSED

Open valve

Model PVA assembly

has been flooded with

water

Drain Model PVA

assembly

5.4.5

Strainer at Model PVA is

clogged

Replace strainer

5.4.6

Model SC-W assembly

NOT

producing 98%

nitrogen when

checked with Model

NA-2 analyzer

Contact

UNITED

Fire Systems

Excessive compressor

runtime (more than 2-

1/2 hours per day)

during purging

During purging, the Model SC-W assembly compressor is supplying air to make nitrogen for

purging. Runtime during purging will be much greater during purging, and “excessive”

runtime is normal. Air compressor runtime should be assessed after purging is complete.

Содержание Nitrogen Pac SC-W

















































































































Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Бренды по названию

Популярные бренды

UNITED Nitrogen Pac SC-W, Установка, наладка, обслуживание

Результаты поиска

Содержание Nitrogen Pac SC-W

Отзывы:

Бренды по названию

Популярные бренды