UNITED Nitrogen Pac SC-W страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 112

background image

UNITED FIRE SYSTEMS

NITROGEN-

PAC™

MODEL SC-W

INSTALLATION, COMMISSIONING, AND MAINTENANCE MANUAL

REVISION 1.01 MAR 2021 - P/N 30-NPWICM-000

36

3.2.5 Drain Connection.

IMPORTANT

Local regulations may require the installation of an oil / water separator in condensate drain piping. Verify local

requirements before completing installation.

UNITED

Fire Systems

does not supply oil / water separators.

(a) Drain Piping.

All points on the Model SC-W assembly requiring drainage are connected to one point. Install drain

piping from Model SC-W drain connection to an appropriate drain location. Refer to

Figure 2

for location of drain

connection. Drain run may be pipe or tubing. Consult with relevant Authorities Having Jurisdiction, local codes, or
building owner for approved materials and discharge location.

(b)

Condensate Pump (Installer provided option)

. A condensate pump may be needed if drain is above the Model

SC-W assembly drain outlet, or if drain is some distance from the Model SC-W installation location.

UNITED

Fire

Systems

does not supply condensate pumps. It is recommended that this drain be run to a building drain or an

environmentally-approved condensate collection / disposal system.

(c) Oil / Water Separator (Installer provided option).

If run to a building drain, environmental regulations may

require installation of an oil / water separator.

3.2.6 Electrical Connections.

DANGER

RISK OF ELECTROCUTION

Voltages and currents associated with the Model SC-W assembly are

LETHAL

. Follow all instructions

provided. Work involving electric power MUST be performed ONLY by qualified individuals. All required
precautions to prevent contact with live electrical conductors MUST be taken. Failure to comply with these
instructions is an immediate hazard with a likelihood of death or serious personal injury!

3.2.6.1 General.

(a) Codes.

All wiring and wiring methods shall be in strict compliance with NEC and local codes.

(b) Personnel.

All wiring shall be performed by a licensed electrician.

(c) Power Supply Specification.

The Model SC-W assembly uses 120 VAC, 60 Hz, single-phase, 3-wire (HOT,

NEUTRAL, GROUND) power, and draws 14 A.

(d) Power for Accessories.

UNITED

Fire Systems

recommends that power for accessories (such as a condensate

pump) be a separate wiring run from its own circuit breaker, and not be combined with the Model SC-W assembly
power or connected to the Model SC-W assembly terminal strip.

(e) Wire Size.

Refer to

Table 6.

«
...
45
46
47
48
49
...
»

Содержание Nitrogen Pac SC-W

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Nitrogen Pac SC-W

Бренд: Rain Bird Страницы: 8

Бренд: Water Tec Страницы: 20

Бренд: Cadman Страницы: 76

Streetpilot C320

Бренд: Garmin Страницы: 8

StreetPilot c340

Бренд: Garmin Страницы: 44

nuvi 800 series

Бренд: Garmin Страницы: 12

GPSMAP 8400 series

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 20

StreetPilot c330

Бренд: Garmin Страницы: 8

Бренд: Safeline Страницы: 76

Бренд: Aiphone Страницы: 4

Бренд: Bticino Страницы: 2

Бренд: Nibe Страницы: 16

STREET SMART MFS

Бренд: McNeilus Страницы: 8

NeuroKom IP DS 935-SH

Бренд: Gehrke Страницы: 8

Бренд: Toray Страницы: 45

Бренд: LaserLiner Страницы: 40

Бренд: Ultra Reef Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды