Unipulse TM700 Скачать руководство пользователя страница 80

Страница: 80 / 91

SUPPLEMENTS

Chapter

8-1.

Error Display List

When either of the following errors occur, the RUN signal of an external output is turned off.

■

Torque display section

-LOAD

Below the signal input range

-5V

The input electric signal greatly exceeds the signal input

range. This also occurs when an excessive load is applied to

the sensor or the input terminal is opened due to a break in

the cabling, etc..

+LOAD

Beyond the signal input range

+5V

ALM HI

Beyond the alarm HI limit

This occurs when a larger load than expected is applied to

the sensor or calibration is performed below the

measurement range.

Check the calibration and measuring object.

ALM LO

Below the alarm LO limit

OFL1

Below -99999

This occurs when a larger load than expected is applied to

the sensor or calibration is performed below the

measurement range.

Check the calibration and measuring object.

OFL2

Beyond 99999

cErr2

Beyond the zero calibration

range in the positive direction.

The signal input range is greatly exceeded when zero

calibration is performed. Check for an excessive load

applied to the sensor and for breaks.

cErr3

Below the zero calibration

range in the negative direction.

cErr4

Beyond the rated output value

in the positive direction/

negative direction.

Beyond the rated capacity

value.

The signal input range is greatly exceeded when calibration

is performed. In the case of equivalent input calibration,

check the rated output value, and in the case of actual load

calibration, check for an excessive load applied to the sensor

and for breaks.

Also, Check the setting of rated capacity value (display

value) sets it exceeding "±

99999".

cErr5

Rated capacity value = 0

Check the setting of rated capacity value (display value) for

being "0" when calibration is performed.

cErr6

Rated output value 0.000V at

the time of equivalent input

calibration.

Rated output value in the range

of -0.010 to +0.010V at the time

of actual load calibration.

Check the rated output value for being 0.000V when

equivalent input calibration is performed, and the load for

being too light in weight when actual load calibration is

performed.

DZ Err

Digital zero limit error

When the range of zero point correction (deviation from the

zero calibration registered point) by digital zero or zero

tracking exceeds the setting value of digital zero limit,

digital zero limit error occurs. Perform digital zero, etc., in a

proper range.

LO BAT

Lithium battery backup voltage

drop

The voltage of the lithium battery for internal memory

backup has dropped. The battery needs to be replaced. Ask

us for replacement of the battery.

SUPPLEMENTS

Содержание TM700




























































































Результаты поиска

Содержание TM700

Отзывы:

Похожие инструкции для TM700

Бренды по названию

Популярные бренды

Unipulse TM700, Руководство по эксплуатации

Результаты поиска

Содержание TM700

Отзывы:

Похожие инструкции для TM700

Бренды по названию

Популярные бренды