Unipulse TM700 Скачать руководство пользователя страница 74

Страница: 74 / 91

OPTION

Chapter

■

Output data select

≪

Setting value

≫

Hold Sync., Hold Not Sync., Zero Scale, Full Scale

Hold Sync.:

Output is produced in synchronization with the indicated value.

Hold Not Sync.:

Outputs value without hold even when the indicated value is on hold.

Zero Scale:

Output is fixed at zero output (0V).

Full Scale:

Output is fixed at full scale (10V).

* Set torque, rotation speed and power, respectively.

How to set

How to output adjust

Select each fixed output in D/A output select, and press the

button, and then use the

simulated trimmer appearing on the adjustment screen to adjust the output.
While monitoring the output value, make fine adjustment of the output with the UP/DOWN

button of the simulated trimmer, and determine by pressing the

button, so

that the trimmer position is entered.

* Pressing the simulated trimmer

buttons continuously performs continuous

operation.

* The trimmer adjusting ranges are as follows: voltage output; about

2.0V.

* The [Clear] button resets the Simulated trimmer position to the trimmer center point (0%).

SET.

Option Setting (D/A Output)

Page 1

→

System Setting

→

Clear button

Simulated trimmer

adjustment

(The trimmer moves to

the directly-pressed place.)

Output channel during

Scale during adjustment

・

DOWN button

position display

adjustment

Содержание TM700




























































































Результаты поиска

Содержание TM700

Отзывы:

Похожие инструкции для TM700

Бренды по названию

Популярные бренды

Unipulse TM700, Руководство по эксплуатации

Результаты поиска

Содержание TM700

Отзывы:

Похожие инструкции для TM700

Бренды по названию

Популярные бренды