Unigas HR2050 Скачать руководство пользователя

Страница: 36 / 80

PART III: OPERATION

Main page

Set point:

temperature set-point

Act value:

actual temperature value

Load:

load percentage (burner output)

Flame:

percentage of flame detection current.

By pressing the ENTER key the display shows the second page:

Second page

Fuel

: it shows (in degrees) the fuel actuator position.

Air

: it shows (in degrees) the air actuator position.

Ax1..3

: auxiliaries.

VSD

: % value on the inverter maximum frequency

: oxygen percentage

: load percentage (burner output).

Press the ENTER key to go back to the main page.
To access the

main menu

, from the main page, press the ESC key tiwce:

Main menu

By pressing the ESC key once, the

Operational Status

(first item in the main menu) menu is directly shown:

the

Operational Status

menu provides the following items:

Normal operation:

by selecting this item and pressing the ENTER key, the main page is showed; press ESC to go back to the main

menu.

Status/Reset:

it shows system errors or faults occuring / it represents the lockout reset function.

Fault History:

by selecting this item and pressing the ENTER key, the Lockout History will be showed about the last 21 faults occured.

Lockout History:

by selecting this item and pressing the ENTER key, the Lockout History will be showed about the last 9 lockouts

occured, and the related date and hour.

Alarm act/deact:

enable/disable the horn in case of alarm.

Fault History

To visualise the

Fault History

, select it and press the ENTER key. The message will be as:

Fuel

0.0

Air

1.8

VSD

0.0

Ld.

0.0

OperationalStat
Operation
ManualOperation

Params & Display

Normal operation
Status/Reset
Fault History
Lockout History

1 Class:

05Gas

code

Phase:

Diag.: 00

Lod:

0.0

Start No.

Содержание HR2050

















































































Результаты поиска

Содержание HR2050

Отзывы:

Похожие инструкции для HR2050

Бренды по названию

Популярные бренды

Unigas HR2050, Руководство по установке, использованию и обслуживанию

Результаты поиска

Содержание HR2050

Отзывы:

Похожие инструкции для HR2050

Бренды по названию

Популярные бренды