ULTRASTOR ULTRA 12F24 Скачать руководство пользователя | Manualshive

Страница: 42 / 52

background image

APPENDIX F

2. In "Select the File System" menu, choose the "High Performance File

System" option (follow disk duplexing function) and proceed with the OS/2
Installation.

LAN Manager Installation

1. After the OS/2 system is installed successfully, reboot the system.

2. Insert Disk 1, LAN Manager "OS/2 - SETUP" diskette, into drive A.

3. Go to the OS/2 Full Screen and type "A:SETUP" and press the return key.

4. Proceed with the installation until the "Install LAN Manager" menu

appears and then select the "Server" option.

Refer to the LAN Manager documentation for a detailed description on installation.

Fault Tolerance Setup

1. After the LAN Manager is successfully installed, go to the OS/2 window.

2. Run "FDISKPM" program to create a partition.

3. Run "FTSETUP" program to setup the fault tolerant parameters.

Refer to the OS/2 documentation for a detailed description on all of the above.

Page F-4

Reference Manual

«
...
40
41
42
43
44
...
»

Содержание ULTRA 12F24





















































Отзывы:

Нет отзывов

Похожие инструкции для ULTRA 12F24

Бренд: jbc Страницы: 4

Бренд: Eaton Страницы: 166

Бренд: K&K Страницы: 6

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Barco Страницы: 6

Бренд: Campbell Страницы: 34

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды