background image

APPENDIX B

setup   is   necessary.     The   tape   utility   program   will   directly   address   the
controller 3rd floppy hardware.

2. If the 3rd floppy drive is intended to be used in the DOS operating system

as a logical block device, the following procedure is used to install the 3rd
floppy device drive.

3. Copy DRIVER.SYS provided with DOS 3.2 and above, and the UltraStor

3rd floppy device driver file  (EXFDRV.SYS) onto your usual boot drive.

4. Modify or create CONFIG.SYS by adding 2 lines shown below.

DEVICE=EXFDRV.SYS /1:xx

where xx =

1 for 360KB drive
2 for 1.2MB drive
3 for 720KB drive
4 for 1.44MB drive

DEVICE=DRIVER.SYS /D:2/T:aa/S:bb/H:2/F:cc 

where aa =

40 for 360KB

bb = 9 for 360KB and 720KB

80 for all others

15 for 1.2M
18 for 1.44MB

And where

cc =

0 for 360KB
1 for 1.2MB
2 for 720KB
7 for 1.44MB

Refer to the DOS manual for detailed explanation on the usage of 
DRIVER.SYS.

5. Reboot the computer again. The computer will go through the normal boot

procedure with 3 additional sign-on messages of the 3rd floppy BIOS and
DRIVER.SYS as follows:

EXFDRV V1.xx     (C) Copyright 1990

 UltraStor Corp.   Registered Number xxxxxx    Loaded External Disk Driver for
Drive "?"
 (where "?" is the next available drive letter assigned by DOS).  The 3rd floppy is
now ready to be used.

Reference Manual

Page B-3

Содержание ULTRA 12F24





















































Отзывы: