Ublox SARA-R4 Series страница 57 Скачать руководство пользователя | Manualshive

Страница: 57 / 307

background image

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

7 Network service

Page 57 of 307

7.12 eDRX sCEDRXS

+CEDRXS

SARA-R410M-02B SARA-R410M-52B

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

No

No

No

-

7.12.1 Description

Configures the UEs extended discontinuous reception (eDRX) parameters. The command controls whether the
UE wants to apply the eDRX or not, as well as the requested eDRX value for each specified type of radio access
technology. If the requested eDRX value is not provided in set command, then the UE will use the eDRX value
provided by the network.

The set command also enables the +CEDRXP URC, that is issued on any change in the eDRX parameters, when
enabled by the network.

The set command with <mode>=3, will disable the use of eDRX and reset all parameters to
factory-programmed values. Optional parameters are not provided in this form of command.

7.12.2 Syntax

Type

Syntax

Response

Example

Set

AT+CEDRXS=<mode>[,<AcT_
type>[,<Requested_eDRX_value>]]

OK

AT+CEDRXS=1,4,"0101"

OK

Read

AT+CEDRXS?

[+CEDRXS: <AcT_type>,
<Requested_eDRX_value>

[...]

[+CEDRXS: <AcT_type>,
<Requested_eDRX_value>]]

OK

+CEDRXS: 4,"0101"

OK

Test

AT+CEDRXS=?

+CEDRXS: (list of supported
<mode>s),(list of supported
<AcT_type>s),(list of supported
<Requested_eDRX_value>s)

OK

+CEDRXS: (0-3),(4-5),("0000"-"1111")

OK

URC

+CEDRXP: <AcT_type>[,
<Requested_eDRX_value>[,<NW-
provided_eDRX_value>[,<Paging_
time_window>]]]

+CEDRXP: 4,"1010","1001","1101"

7.12.3 Defined values

Parameter

Type

Description

<mode>

Number

Indication to disable or enable the use of eDRX in the UE. Allowed values:
•

0 (default value): use of eDRX disabled

•

1: use of eDRX enabled

•

2: enable the use of eDRX and enable the URC

•

3: disable the use of eDRX and reset all parameters for eDRX to factory-
programmed values

<AcT_type>

Number

Indicates the type of access technology. Allowed values:
•

4: E-UTRAN (WB-S1 mode)

•

5: E-UTRAN (NB-S1 mode)

<Requested_eDRX_
value>

String

Requested extended DRX parameters information element, half a byte in a 4 bit
format. For the coding and the value range, see the extended DRX parameters
information element in Table 10.5.5.32 of 3GPP TS 24.008 [

<NW_provided_
eDRX_value>

String

New provided extended DRX parameters information element, half a byte in a 4
bit format. For the coding and the value range, see the extended DRX parameters
information element in Table 10.5.5.32 of 3GPP TS 24.008 [

«
...
55
56
57
58
59
...
»

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SARA-R4 Series

Бренд: E-fly Страницы: 16

Бренд: TCS Basys Controls Страницы: 2

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Barco Страницы: 6

Бренд: Campbell Страницы: 3

Бренд: National Instruments Страницы: 14

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: Aqua Lung Страницы: 24

Бренд: Fagor Страницы: 8

Бренд: Eaton Страницы: 2

Бренд: Ebyte Страницы: 20

EG-PWC-PSWRC-01

Бренд: Energenie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды