manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 3

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

Preface

Page 3 of 307

Preface

Applicable products

This document applies to the following products:

Name

Type number

Modem version

Application version

PCN reference

SARA-R404M

SARA-R404M-00B-00

K0.0.00.00.07.06

N.A.

UBX-17047084

SARA-R410M

SARA-R410M-01B-00

SARA-R410M-02B-00

SARA-R410M-52B-00

L0.0.00.00.02.03

L0.0.00.00.05.06

L0.0.00.00.06.04

N.A.

A02.00

A02.05

UBX-17051617

UBX-18010263

UBX-18020937

SARA-R412M

SARA-R412M-02B-00

M0.04.01

A01.04

UBX-18019641

SARA-N410

SARA-N410-02B-00

L0.0.00.00.07.04

A02.05

UBX-18020938

How to use this Manual

The u-blox Cellular Modules AT Commands Manual provides the necessary information to successfully design
in and configure the applicable u-blox cellular modules.

This manual has a modular structure. It is not necessary to read it from the beginning to the end.

The following symbols are used to highlight important information within the manual:

An index finger points out key information pertaining to module integration and performance.

A warning symbol indicates actions that could negatively impact or damage the module.

Summary table

The summary table on the top of each command section is a quick reference for the user.

command_name

TOBY-L2 MPCI-L2
LISA-U110 LISA-U120 LISA-U130 LISA-U2

Modules

LEON-G1 SARA-G3

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

No

No

No

-

-

It is composed of two sections:
•

Modules

:  lists  all  the  modules  that  support  the  command.  The  modules  are  grouped  in  rows  by  cellular

standard (i.e. L for LTE high data rate (Cat 3 and above), R for LTE low data rate (Cat 1 and below), U for
UMTS/HSPA,  G  for  GSM/GPRS).  In  each  row  the  modules  are  grouped  by:  form  factor  (i.e.  SARA,  LISA),
 platform technology (e.g. SARA-G), platform generation (e.g. SARA-G3), product name (e.g. SARA-G350)
and ordering code (e.g. SARA-G350-00S). In example: if 'LISA-U2' is reported, the command applies to all
the modules having LISA form factor, second chipset version provided with any release of firmware.

•

Attributes

o

Syntax

-

full

: the command syntax is fully compatible among all the products listed in the "Modules" section

-

partial

:  the  products  support  different  syntaxes  (usually  backward  compatible  with  respect  to

previous cellular standards)

o

PIN required

-

Yes

: it is necessary to insert the PIN before the set and/or read command execution

-

No

: the PIN insertion is not needed to execute the command

o

Settings saved

-

Profile

: the command setting can be saved in a personal profile as specified in 

Chapter 1.2

-

NVM

: the command setting is saved in the non-volatile memory as specified in 

Chapter 1.2

-

No

: the current command setting is volatile and cannot be saved

o

Can be aborted

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды