Ublox SARA-R4 Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 307

Ublox SARA-R4 Series Скачать руководство пользователя страница 41

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

7 Network service

Page 41 of 307

7.2.2 Syntax

Type

Syntax

Response

Example

Action

AT+CSQ

+CSQ: <rssi>,<qual>

OK

+CSQ: 2,5

OK

Test

AT+CSQ=?

+CSQ: (list of supported <rssi>s),
(list of supported <qual>s)

OK

+CSQ: (0-31,99),(0-7,99)

OK

7.2.3 Defined values

Parameter

Type

Description

<rssi>

Number

The allowed range is 0-31 and 99. Remapped indication of the following parameters:
•

the Received Signal Strength Indication (RSSI) in GSM RAT

•

the Received Signal Code Power (RSCP) in UMTS RAT

•

the Reference Signal Received Power (RSRP) in LTE RAT

When the RF power level of the received signal is the highest possible, the value 31
is reported. When it is not known, not detectable or currently not available, 99 is
returned.

<qual>

Number

The allowed range is 0-7 and 99. The information provided depends on the selected
RAT:
•

In 2G RAT CS dedicated and GPRS packet transfer mode indicates the Bit Error
Rate (BER) as specified in 3GPP TS 45.008 [

]

•

In 2G RAT EGPRS packet transfer mode indicates the Mean Bit Error Probability
(BEP) of a radio block. 3GPP TS 45.008 [

] specifies the range 0-31 for the Mean

BEP which is mapped to the range 0-7 of <qual>

•

In UMTS RAT indicates the Energy per Chip/Noise (ECN0) ratio in dB levels of
the current cell. 3GPP TS 25.133 [

] specifies the range 0-49 for EcN0 which is

mapped to the range 0-7 of <qual>

•

In LTE RAT indicates the Reference Signal Received Quality (RSRQ). TS 36.133 [

]

specifies the range 0-34 for RSRQ which is mapped to the range 0-7 of <qual>

See

for the complete parameter mapping

7.2.4 Notes

<qual>

2G RAT CS and GPRS

2G RAT EGPRS

UMTS RAT

LTE RAT

0

BER < 0.2%

28 <= MEAN_BEP <= 31

ECN0_LEV >= 44

RSRQ_LEV < 5

1

0.2% < BER < 0.4%

24 <= MEAN_BEP <= 27

38 <= ECNO_LEV < 44

5 <= RSRQ_LEV < 10

2

0.4% < BER < 0.8%

20 <= MEAN_BEP <= 23

32 <= ECNO_LEV < 38

10 <= RSRQ_LEV < 14

3

0.8% < BER < 1.6%

16 <= MEAN_BEP <= 19

26 <= ECNO_LEV < 32

14 <= RSRQ_LEV < 18

4

1.6% < BER < 3.2%

12 <= MEAN_BEP <= 15

20 <= ECNO_LEV < 26

18 <= RSRQ_LEV < 22

5

3.2% < BER < 6.4%

8 <= MEAN_BEP <= 11

14 <= ECNO_LEV < 20

22 <= RSRQ_LEV < 26

6

6.4% < BER < 12.8%

4 <= MEAN_BEP <= 7

8 <= ECNO_LEV < 14

26 <= RSRQ_LEV < 30

7

BER > 12.8%

0 <= MEAN_BEP <= 3

ECNO_LEV < 8

RSRQ _LEV >= 30

99

Not known or not detectable

Table 3: <qual> parameter mapping for each supported RAT

SARA-R404M / SARA-R410M / SARA-N4

• Only LTE RAT is supported.
• The <qual> parameter is not supported, and will be always set to 99.

«
...
39
40
41
42
43
...
»

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов