manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 304

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

Related documents

Page 304 of 307

84.

3GPP  TS  51.010-2  Mobile  Station  (MS)  conformance  specification;  Part  2:  Protocol  Implementation
Conformance Statement (PICS) proforma specification

85.

3GPP TS 34.121-2 User Equipment (UE) conformance specification; Radio transmission and reception
(FDD); Part 2: Implementation Conformance Statement (ICS)

86.

u-blox Firmware Update Application Note, Docu No UBX-13001845

87.

PCCA standard - Command set extensions for CDPD modems, Revision 2.0, March, 1998

88.

3GPP TS 24.301 Non-Access-Stratum (NAS) protocol for Evolved Packet System (EPS); Stage 3

89.

3GPP TS 44.060 General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS)
interface; Radio Link Control / Medium Access Control (RLC/MAC) protocol

90.

3GPP TS 23.221 Architectural requirements

91.

3GPP TS 23.203 Policy and charging control architecture

92.

3GPP TS 31.101 UICC-terminal interface; Physical and logical characteristics

93.

ETSI  TS  102  221  V8.2.0  (2009-06)  Smart  Cards;  UICC-Terminal  interface;  Physical  and  logical
characteristics (Release 8)

94.

RFC 4291 - IP Version 6 Addressing Architecture (

http://tools.ietf.org/html/rfc4291

)

95.

3GPP  TS  25.305  User  Equipment  (UE)  positioning  in  Universal  Terrestrial  Radio  Access  Network
(UTRAN); Stage 2

96.

3GPP TS 23.032: Universal Geographical Area Description (GAD)

97.

TOBY-L2 series Networking Modes Application Note, Docu No UBX-14000479

98.

3GPP TS 25.331 Radio Resource Control (RRC); Protocol specification

99.

3GPP  TS  36.101  Evolved  Universal  Terrestrial  Radio  Access  (E-UTRA);  User  Equipment  (UE)  radio
transmission and reception

100.

Wi-Fi / Cellular Integration Application Note, Docu No UBX-14003264

101.

3GPP TS 24.173 IMS Multimedia telephony communication service and supplementary services; Stage 3

102.

3GPP TS 24.341 Support of SMS over IP networks; Stage 3

103.

3GPP  TS  24.229  IP  multimedia  call  control  protocol  based  on  Session  Initiation  Protocol  (SIP)  and
Session Description Protocol (SDP); Stage 3

104.

3GPP TS 36.306 Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) radio access
capabilities

105.

3GPP TS 36.133 Evolved Universal Terrestrial Radio Access (E-UTRA); Requirements for support of radio
resource management

106.

3GPP TS 25.133 Requirements for support of radio resource management (FDD)

107.

3GPP TS 22.071 Location Services (LCS); Service description

108.

IEC 61162 Digital interfaces for navigational equipment within a ship

109.

3GPP TS 36.331 Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Resource Control (RRC);
Protocol specification (Release 10)

110.

3GPP TS 24.167 3GPP IMS Management Object (MO); Stage 3

111.

ITU-T E.212 - Series E: Overall network operation, telephone service, service operation and human factors

112.

RFC 793 - Transmission Control Protocol (TCP) Protocol Specification (

https://www.rfc-editor.org/rfc/

rfc793.txt

)

113.

3GPP TS 26.201 Speech codec speech processing functions; Adaptive Multi-Rate - Wideband (AMR-WB)
speech codec; Frame structure

114.

3GPP TS 24.216 Communication Continuity Management Object (MO)

115.

3GPP TS 36.521-2 - Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment conformance
specification; Radio transmission and reception; Part 2: Implementation Conformance Statement (ICS)

116.

3GPP TS 36.523-2 - Evolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet Core (EPC);
User Equipment conformance specification; Part 2: Implementation Conformance Statement (ICS)

117.

3GPP TS 23.003 Numbering, addressing and identification

118.

TOBY-L2 series Audio Application Note, Docu No UBX-15015834

119.

3GPP TS 31.111 Universal Subscriber Identity Module (USIM) Application Toolkit (USAT)

120.

RFC 3969 - The Internet Assigned Number Authority (IANA) Uniform Resource Identifier (URI) Parameter
Registry for the Session Initiation Protocol (SIP)

121.

RFC 3261 - SIP: Session Initiation Protocol

122.

RFC  5341  -  The  Internet  Assigned  Number  Authority  (IANA)  tel  Uniform  Resource  Identifier  (URI)
Parameter Registry

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды