Ublox SARA-R4 Series страница 35 Скачать руководство пользователя

Страница: 35 / 307

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

5 Mobile equipment control and status

Page 35 of 307

Type

Syntax

Response

Example

Test

AT+CSGT=?

+CSGT: (list of supported <mode>s),
<ltext>

+CSGT: (0-1),49

5.7.3 Defined values

Parameter

Type

Description

<text>

String

Greeting text. The factory-programmed value is the empty string.

<mode>

Number

•

0: turn off the greeting text

•

1: turn on the greeting text

<ltext>

Number

Maximum length of the <text> parameter.

5.8 Automatic time zone CTZU

+CTZU

SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

Yes

NVM

+CME Error

5.8.1 Description

Configures the automatic time zone update via NITZ.

The Time Zone information is provided after the network registration (if the network supports the time
zone information).

5.8.2 Syntax

Type

Syntax

Response

Example

Set

AT+CTZU=<on_off>

AT+CTZU=1

Read

AT+CTZU?

+CTZU: <on_off>

+CTZU: 0

Test

AT+CTZU=?

+CTZU: (list of supported <on_
off>s)

+CTZU: (0-1)

5.8.3 Defined values

Parameter

Type

Description

<on_off>

Number

Allowed values (see

Notes

for the factory-programmed value):

•

0: automatic time zone via NITZ disabled

•

1: automatic time zone update via NITZ enabled; if the network supports the service,
the local time of the module is changed (not only time zone)

5.8.4 Notes

SARA-R4 / SARA-N4

• The factory-programmed value of the <on_off> parameter is 0.

Содержание SARA-R4 Series




















































































































































































































































































































Результаты поиска

Содержание SARA-R4 Series

Отзывы:

Похожие инструкции для SARA-R4 Series

Бренды по названию

Популярные бренды

Ublox SARA-R4 Series, Руководство по управлению

Результаты поиска

Содержание SARA-R4 Series

Отзывы:

Похожие инструкции для SARA-R4 Series

Бренды по названию

Популярные бренды