manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 293

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

B    Appendix: AT Commands List

Page 293 of 307

AT command

Description

AT interface
configuration
sharing

Factory-programmed value / Remarks

V

DCE response
format

No

1 (Verbose response text)

X

Result code selection
and call progress
monitoring control

No

4 (CONNECT <text> result code is given upon entering online
data state; dial tone and busy detection are both enabled)

B.2    Parameters stored in non volatile memory

The following table lists the AT commands which setting can be stored in the non volatile memory with their
parameters and the factory-programmed values.

AT command

Description

Factory-programmed value / Comment

+CCLK

Clock

04/01/01,00:00:00+00

+CEMODE

UE modes of operation for EPS •

SARA-R4 / SARA-N4 - 2 (CS/PS mode 2 of operation; "data centric")

+CGDCONT

PDP context definition

•

SARA-R4 / SARA-N4 - all contexts are undefined

+CPMS

Preferred message storage

•

SARA-R4  /  SARA-N4  -  <mem1>,  <mem2>  and  <mem3>  are  set  to
"ME"

+CPSMS

Power Save Mode

•

SARA-R4 / SARA-N4 - 0 (PSM disabled)

+CSAS

Save settings

0 (profile 0 where to store the active message settings)

+CSGT

Set greeting text

Greeting text is empty

+CTZU

Automatic time zone update

•

SARA-R4 / SARA-N4 - 0 (automatic time zone via NITZ disabled)

+UBIP

Bearer Independent Protocol
status indication

0 (BIP status indication disabled)

+UDCONF=75

PDP IP configuration when
roaming

•

SARA-R4 / SARA-N4 - no context is undefined

+UDCONF=76

Configure data when roaming •

SARA-R4 / SARA-N4 - no context is undefined

+UFOTACONF

LWM2M configuration

1 (module registration to uFOTA server enabled, 604800 (7 days as
timer for the periodic connection to the uFOTA server)

+UGGGA

Get GPS fix data

0 (NMEA $GGA messages disabled)

+UGGLL

Get geographic position

0 (NMEA $GLL messages disabled)

+UGGSA

Get satellite information

0 (NMEA $GSA messages disabled)

+UGGSV

Get number of GNSS satellites
in view

0 (NMEA $GSV messages disabled)

+UGPIOC

GPIO functionality setting

•

SARA-R4 / SARA-N4 - 255 (<gpio1>), 255 (<gpio2>), 255 (<gpio3>),
 255 (<gpio4>), 255 (<gpio5>), 255 (<gpio6>)

+UGPRF

GNSS profile configuration

0 (No data flow on multiplexer, file and IP address), 0 (IP port not
defined), "" (Server address string not defined)

+UGRMC

Get recommended minimum
GNSS data

0 (NMEA $RMC messages disabled)

+UGSRV

Aiding server configuration

"cell-live1.services.u-blox.com" (primary MGA server), "cell-
live2.services.u-blox.com" (secondary MGA server), 14 (Number of days
for validation of Offline data), 4 (Number of weeks for validation of
Offline data), 1 (Resolution of offline data for MGA), 65 (Desired GNSS
for the (offline) aiding: GPS and GLONASS), 0 (AssistNow Online data
are downloaded at GNSS receiver power up), 15 (all the desired data
types for the (online) aiding are set)

+UGVTG

Get course over ground and
ground speed

0 (NMEA $VTG messages disabled)

+UGZDA

Get GPS time and date

0 (NMEA $ZDA messages disabled)

+ULGASP

Last gasp configuration

•

SARA-R4 / SARA-N4
o

<GPIO_mode>: 0 (disabled)

o

<text>: ""

o

<msg_format>: 0 (text)

o

<profile_id>: 1

o

<IP_protocol>: 17 (UDP)

o

<IP_addr:PORT>: "" (empty)

o

<method>: 1 (use IP (TCP or UDP) connection)

o

<urc_enable>: 1 (URC enabled)

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды