Ublox SARA-R4 Series страница 207 Скачать руководство пользователя | Manualshive

Страница: 207 / 307

background image

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

19 SSL/TLS

Page 207 of 307

provides the list the applicability of SSL connection properties depending on the module series.

Certificate validation level

Minimum SSL/TLS version

Cipher suite

Trusted root certificate internal name

Expected server hostname

Password for the client private key

Pre-shared key used for connection

SNI

SARA-R4 SARA-N4

*

*

*

*

*

Table 21: SSL/TLS connections properties applicability

To set all the parameters in security profile, a set command for each <op_code> needs to be issued (e.g.
certificate validation level, minimum SSL/TLS version, ...).

To reset (set to factory programmed value) all the parameters of a specific security profile, issue the AT
+USECPRF=<profile_id> command.

19.3.2 Syntax

Type

Syntax

Response

Example

Set

AT+USECPRF=<profile_id>[,<op_
code>[,<param_val>]]

OK

AT+USECPRF=0,0,0

OK

Read

AT+USECPRF=<profile_id>,<op_
code>

+USECPRF: <profile_id>,<op_code>,
<param_val>

OK

AT+USECPRF=0,0

+USECPRF: 0,0,0

OK

Test

AT+USECPRF=?

+USECPRF: (list of supported
<profile_id>s),(list of supported
<op_code>s)

OK

+USECPRF: (0-4),(0-6)

OK

19.3.3 Defined values

Parameter

Type

Description

<profile_id>

Number

USECMNG security profile identifier, in range 0-4; if it is not followed by other parameters the
profile settings will be reset (set to factory programmed value).

<op_code>

Number

•

0: certificate validation level; allowed values for <param_val>:
o

0 (factory-programmed value): Level 0 - No validation; the server certificate will not be
checked or verified. The server in this case is not authenticated.

o

1: Level 1 - Root certificate validation without URL integrity check. The server certificate
will be verified with a specific trusted certificates or with each of the imported trusted root
certificates.

o

2: Level 2 - Root certificate validation with URL integrity check. Level 1 validation with an
additional URL integrity check.

o

3: Level 3 - Root certificate validation with check of certificate validity date. Level 2
validation with an additional check of certificate validity date.

•

1: minimum SSL/TLS version; allowed values for <param_val>:
o

0 (factory-programmed value): any; server can use any version for the connection.

o

1: TLSv1.0; connection allowed only to TLS/SSL servers which support TLSv1.0/TLSv1.1/
TLSv1.2

o

2: TLSv1.1; connection allowed only to TLS/SSL servers which support TLSv1.1/TLSv1.2

o

3: TLSv1.2; connection allowed only to TLS/SSL servers which support TLSv1.2

•

2: cipher suite; allowed values for <param_val> define which cipher suite will be used:

«
...
205
206
207
208
209
...
»

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SARA-R4 Series

Бренд: GE Страницы: 425

Бренд: Zeagle Страницы: 37

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Partizan Страницы: 7

Бренд: DigiPower Страницы: 27

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: Paradox Страницы: 28

Бренд: PI Страницы: 6

Бренд: CLA-VAL Страницы: 43

Бренд: One for All Страницы: 2

Бренд: Badger Meter Страницы: 66

ERO-32AP-0 V1.4

Бренд: Darco Страницы: 14

Бренд: Rainmachine Страницы: 22

GREYHOUND GRM20

Бренд: Hirschmann Страницы: 36

Бренд: Walther Systemtechnik Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды