manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 46

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

7    Network service

Page 46 of 307

Parameter

Type

Description

•

8: LTE CAT-NB1

•

9: eGPRS

<PreferredAct>

Number

Indicates the preferred access technology; it is ignored if dual mode or tri mode are
not selected.
•

0: GSM

•

2: UTRAN

•

3: LTE

•

7: LTE CAT-M1

•

8: LTE CAT-NB1

•

9: eGPRS

<2ndPreferredAct>

Number

Indicates the second preferred access technology; it is ignored if tri mode is not
selected.
•

0: GSM

•

2: UTRAN

•

3: LTE

•

7: LTE CAT-M1

•

8: LTE CAT-NB1

•

9: eGPRS

7.5.4    Notes

• AT&T's EF

RAT

 mode contains the RAT mode setting, the RAT mode setting is the mode that the module

shall be set to. Thus this setting may ovURAT's <SelectedAcT> and <PreferredAct> loaded at
boot time.

SARA-R404M / SARA-R410M-01B

• <SelectedAcT>=0, 1, 2, 4, 5, 6, 7, 8, 9 are not supported. The factory-programmed value of <SelectedAcT>

is 3.

SARA-R410M-02B / SARA-R410M-52B

• <SelectedAcT> is the first AcT the module will search. In the case a suitable cell can't be found on this

AcT, the module will search the <PreferredAct> if defined.

• <PreferredAct>  is  the  next  AcT  the  module  will  search  if  no  suitable  cell  can  be  found  on  the

<SelectedAcT>.  In  the  case  a  suitable  cell  can't  be  found  on  this  AcT,  the  module  will  search  the
<2ndPreferredAct> if defined.

• <SelectedAcT>=0, 1, 2, 3, 4, 5, 6, 9 are not supported. The factory-programmed value of <SelectedAcT>

is 7.

• <PreferredAct>=0, 2, 3, 9 are not supported. The factory-programmed value of <PreferredAct> is 8.
• <2ndPreferredAct>=0,  2,  3,  9  are  not  supported.  The  factory-programmed  value  of  <PreferredAct>  is

NULL.

SARA-N4

• <SelectedAcT>=0,  1,  2,  3,  4,  5,  6,  7,  8,  9  are  not  supported.  The  factory-programmed  value  of

<SelectedAcT> is 8.

7.6    Network registration CREG

+CREG

SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

partial

No

No

No

-

+CME Error

7.6.1    Description

Configures the network registration information. Depending on the <n> parameter value, a URC can be issued:
• +CREG: <stat> if <n>=1 and there is a change in the MT's circuit switched mode network registration status

in GERAN/UTRAN/E-UTRAN

• +CREG: <stat>[,<lac>,<ci>[,<AcTStatus>]] if <n>=2 and there is a change of the network cell in GERAN/

UTRAN/E-UTRAN

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды