manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 36

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

5    Mobile equipment control and status

Page 36 of 307

5.9    Report mobile termination error +CMEE

+CMEE

SARA-R404M SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

No

No

No

-

+CME Error

5.9.1    Description

Configures the formatting of the result code +CME ERROR: <err> as an indication of an error relating to the
functionality of the MT. When enabled, MT related errors cause +CME ERROR: <err> final result code instead
of the regular ERROR final result code. The error result code is returned normally when an error is related to
syntax, invalid parameters or MT functionality.

5.9.2    Syntax

Type

Syntax

Response

Example

Set

AT+CMEE=[<n>]

OK

AT+CMEE=2

OK

Read

AT+CMEE?

+CMEE: <n>

OK

+CMEE: 0

OK

Test

AT+CMEE=?

+CMEE: (list of supported <n>s)

OK

+CMEE: (0-2)

OK

5.9.3    Defined values

Parameter

Type

Description

<n>

Number

•

0: +CME ERROR: <err> result code disabled and ERROR used

•

1: +CME ERROR: <err> result code enabled and numeric <err> values used

•

2: +CME ERROR: <err> result code enabled and verbose <err> values used

5.9.4    Notes

• The following convention is valid:

Numeric error code Verbose error code

Description

3

"operation not allowed"

The MT is in a state which does not allow performing the
entered command.

4

"operation not supported"

The error result code is related to a parameter not covered by
the GSM/ETSI or u-blox specification

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды