Tuthill 120A Скачать руководство пользователя страница 34

Страница: 34 / 38

Page 34 of 38

Suspended Solids

Solids which are suspended in liquids and which are an inherent part of their structure would include starch, clay slurry, muddy water

and other similar slurries. This is best handled by an external flush of clear liquid through a lantern ring as shown. This arrangement

will result in a small amount of product dilution and is controlled by the differential pressure in the seal chamber.

Installing Tuthill Tuffseal

Cartridge Seals

Once pump is fully disassembled (shafts are removed from the impeller housing and faceplate) one can clean stuffing box and shafts

thoroughly and examine shaft for wear or scoring. Check bearings for wear as this can cause an eccentric shaft rotation resulting in

excessive leakage. If shaft surface is worn, replace shaft or have seal surface area resurfaced.

Install new Tuffseal Cartridge seals to the impeller housing and faceplate by fitting the studs into the seal gland slots. Then install the

washers and nuts to hold the seal gland onto the stuffing box. These nuts should be tightened finger tight so that the seal assembly

can move when the shafts are being installed.

During re-assembly, lubricate both of the seal’s O-rings to and make sure the shafts are guided through the Tuffseal collar. Apply

even pressure when pushing the shaft through the seal as to not damage the collar O-rings.

Once the entire pump is re-assembled, make sure the collar shoulder is seated against the seal spacers.

Tighten the seal gland nuts to secure the Tuffseal to the stuffing box.

After the pump’s end clearance is set, then tighten the collar setscrews evenly to the shaft.

Rotate the spacers away from the collar so that they will not rub against any rotating component when the seal is operating.

Installing Mechanical Seals in Pumps(General)

Once pump is fully disassembled (shafts are removed from the impeller housing and faceplate) one can clean stuffing box and shafts

thoroughly and examine shaft for wear or scoring. Check bearings for wear as this can cause an eccentric shaft rotation resulting in

excessive leakage. If shaft surface is worn, replace shaft or have seal surface area resurfaced.

Install new stationary seal seat into the mechanical seal gland. Use a seal lubricant to aid in pressing the seat into the gland. Do not

scratch or score the seal face during this process as it will result in a leak.

During re-assembly, make sure the mechanical seals and the glands are guided through the shafts as they are installed. Apply even

pressure when pushing the shaft through the seal as to not damage the O-rings or seal bellows.

Once the entire pump is re-assembled, and the correct end clearance is set, reference the correct working length of the seal.

Mark the shaft, through the stuffing box access port, where the correct working length would be on the shaft.

Move the seal body to that mark and tighten the seal setscrews. This sets the correct working height of the mechanical seal. Please

reference the seal’s manual for the correct working height.

Install the seal gland and seal gland gasket to the stuffing box.

Tighten the nuts to the seal gland.

Содержание 120A







































Результаты поиска

Содержание 120A

Отзывы:

Похожие инструкции для 120A

Бренды по названию

Популярные бренды

Tuthill 120A, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 120A

Отзывы:

Похожие инструкции для 120A

Бренды по названию

Популярные бренды