manualshive.com logo in svg

Tuthill 120A, Инструкция по установке и обслуживанию, Страница: 38 / 38

Поделиться
Скачать
Tuthill 120A Скачать руководство пользователя страница 38

Tuthill Pump Group

12500 S. Pulaski Road, Alsip, IL  60803

www.tuthillpump.com

Excellence at work.  Excellence in life.

Material Returns

If it becomes necessary to return a pump to the factory, a Return Goods Authorization (RGA) must be obtained from either your local 

Authorized Distributor or our Alsip plant.  No RGA can be issued until a completed Material Safety Data Sheet (MSDS) has been 

forwarded to our Alsip plant and return of the pump has been approved.

•  Tuthill pumps are precision-built and must be handled with care
• 

Pumps must be drained of all fluid and the ports plugged to prevent foreign material from getting into the pump

•  Pumps must be packaged securely to prevent damage while in transit

Warranty

Tuthill Pump Group warrants its products against defective material and workmanship for 90 days from the date of startup or one year 

from date of shipment from Tuthill’s plant, whichever comes first.  This warranty does not include products damaged by tampering, 

improper installation, abuse, or wear.  Nor does it cover consequential damages, or other losses due to pump failure. Because of the 

unpredictable nature of fluids encountered, pumps are not warranted for any specific life.

Contact Information

If additional information is required to facilitate operation or maintenance, contact the authorized Tuthill distributor shown below. 

Information on Tuthill contacts can also be obtained on our website.

North America

Tuthill Pump Group

12500 S. Pulaski Road

Alsip, Illinois 60803

U.S.A.

[email protected]

Europe

Tuthill UK Ltd.

Manners Industrial Estate

Ilkeston, Derbyshire DE7 8YA

England

[email protected]

Содержание 120A







































Отзывы:

Нет отзывов