manualshive.com logo in svg

Tuthill 120A, Инструкция по установке и обслуживанию, Страница: 8 / 38

Поделиться
Скачать
Tuthill 120A Скачать руководство пользователя страница 8

Page 8 of 38

Packing Adjustment

WARNING

Packing is designed to leak. Therefore, when pumping hazardous liquids, a mechanical seal is recommended to minimize any potential 

source of leakage that could result in a hazardous condition.

All packings must leak to perform properly.  Their purpose is to control leakage—not to prevent it. The slight leakage along the shaft 

provides proper lubrication to the packing.  Pump packings have a lubricant, which acts as a primary sealant for the start-up and break-

in phases, during which this lubricant acts to reduce friction.  Once the pump is on the line, external lubrication must be supplied to the 

packing to keep it running properly and to attain longer life.  If external lubrication is not supplied, the lubrication in the packings will 

bleed out due to heat generation.  Heat is a primary cause of packing failure. Pumps with packing will require periodic adjustment. To 

accomplish this, gently and evenly tighten the packing gland nuts, which will further compress the packing. Do not over-tighten.  Packing 

is designed to keep leakage to a slight weep.  Normally 2-3 drops per minute is acceptable. If excessive leakage persists after complete 

adjustment, consider re-packing the stuffing box or using another packing type.

Lubrication Requirements

•  Faceplate Bearings- The faceplate bearings are greased. Grease should be added to faceplate bearings when oil is changed.  

Add grease through fitting until new grease can be seen exiting under lip seal where shaft enters bearing.  Bearings are 

designed to provide a minimum L10 life of 15,000 hours at maximum speed and pressures conditions. 

• 

Housing Bushing- Housing bushings are fully lubricated by the pumped fluid and are maintenance free.

•  Gear Case Bearings- Bearings are designed to provide a minimum L10 life of 15,000 hours at maximum speed and pressures 

conditions and are splashed lubricated.

Lubrication Instructions for Tuthill Process Pumps

The oil in the gear case of the process pumps is “Lubriplate” APG9 a trade name of Fiske Brothers Refining Company – Toledo, Ohio.

Oil specifications are as follow

Viscosity at 100°F:  816 SSU

Viscosity at 212°F:  86 SSU

API Gravity:  26.5

Flash Point:  39°F

Fire Point:  440°F

Extreme Pressure Additives

Any 90-weight gear oil may be substituted if equivalent to above

The grease used in the faceplate ball bearing of the Industrial Series pump is “Lubriplate” 1200-2

Grease specifications are as follows

Lithium Base

N.L.G.I. #2

Work Penetration:  280

A.S.T.M. Dropping Point: 450°F

Minimum Oil Viscosity at 100°F: 950SSU

Water resistant with rust and corrosion inhibitors added

Any #2 bearing grease may be substituted if equivalent to above

Содержание 120A







































Отзывы:

Нет отзывов