Tuthill 120A Скачать руководство пользователя страница 20

Страница: 20 / 38

Page 20 of 38

If Packing is used (reference assembly on page 13). Insert packing (29) and glands (30) in seal chambers on faceplate. Also,

reference Page 39 for additional packing information. If Tuffseals are used (reference assembly on page 15). Install Tuffseals onto

impeller stuffing boxes. Use the gland washers (45) and nuts (32) to hand tighten the seal glands to the stuffing boxes. Do not fully

tighten the nuts. Also, reference Page 40 for additional Tuffseal information. If mechanical seals are used (reference assembly on

page 17). Press in the stationary seal seat into the mechanical seal gland if replacing the seal or re-use the existing one. Have the seal

bodies and seal glands nearby as those will have to be slipped onto the shafts as one is assembling the shafts through the impeller

faceplate. Loosen the pipe plugs (24) so one will have access to the mechanical seal set screws in order to set the correct working

height of the seal. Also, reference Page 41 for additional mechanical seal information.

Insert impeller and shaft assemblies, threaded portion first, through stuffing box, packing/mechanical seal body and seat, Tuffseals,

seal gland, and inner race of faceplate bearing. Secure assemblies in this position by tightening the faceplate bearing lock nuts (15).

V-rings (25) should also be installed while inserting the shafts. Be aware that the V-rings need to be slid onto the shafts because of

their snug fit.

Insert bearing cover (14) in place and tighten bearing hex head bolts (12). The impeller and shaft assemblies are now secure in the

faceplate.

Check the clearance with a feeler gauge, between the machine face of the faceplate and the flat surface on the lobe of the impeller.

This setting clearance will vary with the material of construction and pumping temperature. See chart below for the proper setting

clearance. This clearance is checked by revolving the impeller and shaft 360°, while checking the clearance at multiple positions. All

other clearances are automatically set if this clearance is correct.

Содержание 120A







































Результаты поиска

Содержание 120A

Отзывы:

Похожие инструкции для 120A

Бренды по названию

Популярные бренды

Tuthill 120A, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 120A

Отзывы:

Похожие инструкции для 120A

Бренды по названию

Популярные бренды