Trotec TAC XT 18 страница 2 Скачать руководство пользователя

Страница: 2 / 59

vertical heater TAC XT 18 / TAC XT 27

Table of contents

Notes regarding the instructions .......................................... 2

Safety ..................................................................................... 3

Information about the device................................................ 6

Transport and storage........................................................... 8

Assembly and installation..................................................... 8

Operation ............................................................................. 11

Available accessories.......................................................... 18

Errors and faults.................................................................. 19

Maintenance ........................................................................ 19

Technical annex................................................................... 24

Disposal ............................................................................... 58

Declaration of conformity ................................................... 58

Notes regarding the instructions

Symbols

Warning of electrical voltage

This symbol indicates dangers to the life and health of
persons due to electrical voltage.

Warning of hot surface

This symbol indicates dangers to the life and health of
persons due to hot surface.

Warning

This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.

Caution

This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.

Note

This signal word indicates important information (e.g.
material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry
out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the
instructions must be observed.

Wear foot protection

Information marked with this symbol indicates that you
should wear safety boots.

You can download the current version of the instructions via the
following link:

TAC XT 18

https://hub.trotec.com/?id=46248

TAC XT 27

https://hub.trotec.com/?id=46249

Содержание TAC XT 18




























































Результаты поиска

Содержание TAC XT 18

Отзывы:

Похожие инструкции для TAC XT 18

Бренды по названию

Популярные бренды

Trotec TAC XT 18, Оригинальное руководство пользователя

Результаты поиска

Содержание TAC XT 18

Отзывы:

Похожие инструкции для TAC XT 18

Бренды по названию

Популярные бренды