Trotec IDS 20 Скачать руководство пользователя страница 3

EN

3

oil heater IDS 20 / IDS 30

Warning

Children of less than 3 years should be kept away from
the device unless continuously supervised.
Children aged from 3 years and less than 8 years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or
perform user maintenance.

Warning

Do not use the device in rooms if persons are present
who cannot leave the room independently and who are
not under constant supervision.

• Do not use the device in potentially explosive rooms or

areas and do not install it there.

• Do not use the device in aggressive atmosphere.
• Only put up the device in an upright, stable position on firm

ground.

• Let the device dry out after a wet clean. Do not operate it

when wet.

• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not remove any safety signs, stickers or labels from the

device. Keep all safety signs, stickers and labels in legible
condition.

• Attention: In Germany, the Federal Emission Protection

Directive applies. Do not operate the device for more 
than 3 months at the same place. Prior to planning the flue
gas system, gather information about the national
legislation and contact a responsible specialist.

• Do not sit on the device.
• This appliance is not a toy. Keep away from children and

animals. Do not leave the device unattended during
operation.

• Check accessories and connection parts for possible

damage prior to every use of the device. Do not use any
defective devices or device parts.

• Ensure that all electric cables outside of the device are

protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!

• The mains connection must correspond to the

specifications in the Technical annex.

• Insert the mains plug into a properly fused mains socket.

• Observe the device's power input, cable length and

intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.

• Before carrying out maintenance, care or repair work on

the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from

the mains socket when the device is not in use.

• Do not under any circumstances use the device if you

detect damages on the mains plug or power cable. 
If the power cable is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!

• When positioning the device, observe the minimum

distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
annex.

• Do not use the device in immediate proximity to curtains,

beds or sofas.

• Make sure that the air inlet and outlet are not obstructed.
• Make sure that the suction side is kept free of dirt and

loose objects.

• Do not place the device on combustible ground.
• Only transport the device in an upright position.
• Only use original spare parts, for otherwise safe and

functional operation cannot be ensured.

Intended use

The device was developed for the purpose of generating hot air
and may only be used in roofed over outdoor areas or in well-
ventilated interior spaces whilst adhering to the technical data.
The device is suited for heating large rooms such as tents,
warehouses, workshops, construction sites, greenhouses or
agricultural halls.
It is intended to be used without frequent site changes.
The device may only be used in rooms with sufficient fresh air
supply and exhaust discharge.
The device must only be operated with EL (ultra-light) fuel oil
and diesel, however not with petrol, heavy fuel oil etc.

Содержание IDS 20



























Отзывы: