background image

EN

25

oil heater IDS 20 / IDS 30

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website 
https://hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Fuel oil

The fuel oil must be drained from the device and collected.
Fuels are to be disposed of according to the national
regulations.

Declaration of conformity

The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at 

https://hub.trotec.com/?id=43996

.

Declaration of conformity

in accordance with the EC Machinery Directive 2006/42/EC, 

Annex II, Part 1, Section A

Herewith, we – Trotec GmbH– declare that the machinery
designated below was developed, constructed and produced in
compliance with the requirements of the EC Machinery
Directive in the version 2006/42/EC.

Product model / Product:

IDS 20
IDS 30

Product type:

oil heater

Year of manufacture as of:

2020

Relevant EU directives:

• 2014/30/EU: 29/03/2014

Applied harmonised standards:

• None

Applied national standards and technical specifications:

• None

Manufacturer and name of the authorised representative of
the technical documentation:

Trotec GmbH
Grebbener Straße 7, D-52525 Heinsberg
Phone: +49 2452 962-400
E-mail: [email protected]

Place and date of issue:
Heinsberg, 

01.10.2010

Detlef von der Lieck, Managing Director

Содержание IDS 20



























Отзывы: