background image

Page 20 of 20 

 

power units and/or motors. If any disputes arise, the supplier requires a copy of the invoice from 
the certified electrician with an itemized report of the work done. 

 

The lift is warranted by our supplier for one year. Auto Lifts carry a 2 year structural warranty if 
installed indoors. Warranty is for parts only. No labor warranty exists. Hydraulics and Electronics 
are covered under 1 year parts replacement. Warranty does not cover rubber lifting pads on two 
post lifts. Replacement parts or replacement equipment being sent to the customer does not 
represent an extension or renewal of the warranty period. Shipping of warranted parts is for 
normal ground shipping only within the USA. 
 NOTE:           All Shipping costs are paid by customer after first 60 days of warranty period, no 
exceptions. 

No warranties exist for any incidental cost occurring from loss of use of product. Warranty is not 
transferable. Warranty is issued to original purchaser only and cannot be transferred to anyone 
else. 

Any attempts at charge backs or legal action will void the warranty on the product purchased 
regardless of the decisions made by all companies involved in the transaction and or the 
decision of the courts. Once warranty is voided, it cannot be reinstated. No other warranty is 
expressed or implied. Warranty is governed by the laws of the State of Texas, County of 
Tarrant. Our supplier will not enter into any verbal agreements regarding changes to the stated 
warranty policy. We reserve the right to change or amend any measurements, instructions, 
policies, pictures, and warranties, as stated in our manuals, on our website, and on any other 
printed or published materials, without notice to customers prior to changes being made. 

Any and all vehicles pictured with our products do not imply a set measurement or dimension in 
regards to the lift with which they are pictured.  Purchaser/Customer has read and understands 
the whole of this document and all parts thereof. Purchaser/Customer further understands that 
this document and all parts thereof is governed in whole or in part by the law of the State of 
Texas.  Any action at law, suit in equity, or other judicial proceedings for the enforcement of this 
document or any provision thereof shall be instituted only in the courts of the State of Texas, 
County of Tarrant.  The covenants and conditions contained in this document shall apply to and 
bind the parties, purchasers, customers, heirs, legal representatives and assigns of the parties. 

ISO 9001 AND CE CERTIFICATION 

This lift is built in a factory that carries an ISO-9001 Quality Certification. This is an 
internationally accepted quality control standard. ISO-9001 is overseen by an independent third 
party with no vested interest in the company seeking certifications. The power unit carries the 
CE mark which is a mandatory safety mark and ensures that your products are tested and safe. 

 

 

Содержание NTO-10A





















Отзывы: