background image

Page 9 of 20 

 

 

11. After fastening the cross beam, check and confirm that the remaining column is plumb. 

 

 

 

(Making sure the power column on left and offside column are plumb. Critical.) 

12. Secure the power column, and make plumb. In same fashion as the first column. 
13. At this point you can put in all anchors in both columns once you are sure they are 

positioned properly and plumb and square. Also make sure you have securely bolted the 
top rail. Install the rubber door protectors on both columns with bolts provided. 
 

 

14. Install the equalizing cables. 

a.  Manually set both carriages on the first safety latch. Be sure each carriage is at 

the same height by measuring from the top of the base to the bottom of the 
carriage. DOUBLE CHECK THE LATCHES ARE ENGAGED BEFORE 
WORKING UNDER OR AROUND THE CARRIAGES). This dimension should be 
within ¼”. 

b.  Run the first cable. Tighten nut on one cable stud. Pull the other end of the cable 

and run nut on it. Tighten both nuts. Repeat above for second cable. 

 

Note: the cable stud that connects to the front right corner of the carriage should be 
connected first by pulling the stud through the carriage hold and up where it is easy 
to be held by locking pliers. Pull the stud past the locknut. Connect the other ends to 
the rear right corners of the carriage with at least ½” of thread showing past the lock 
nut (cables run on the inside of the carriage). It may be necessary to manually raise 
both carriages above the cylinder to prodi enough space to use the locking pliers. 
Make sure the carriage is set in the LOCK position. 

Содержание NTO-10A





















Отзывы: